manualshive.com logo in svg

Kubota 2420, Nstruction And Service Manual, Page: 47 / 69

Share
Download
Kubota 2420 Nstruction And Service Manual Download Page 47

５－４

Error

Indicators

Checkpoint

Action taken

E4

Speed sensor error

This  indicator  flashes  when  the 
self-inspection  function  detects the 
fault  or  abnormality in  the  speed 
sensor.

After  the rotor stops spinning,  turn 
off  power  supply once and  turn on 
the  power  after  about 30 seconds. 
When the  error recurs, contact your 
nearest dealer for inspection.

E6

Over speed error

Flashes  to  stop  the rotation  when 
the  maximum  speed  of  the 
corresponding rotor is exceeded. 

Contact   your  local  dealer  for 
inspection  when  this  error 
continues to flash.

E7

Speed error

This  code  appears  when  the 
equipment  did  not  start  its 
operation  within  5  seconds  after 
the "START"  key was  pressed by 
such  causes  as  electric  circuit 
failures.

After  the rotor stops spinning,  turn 
off the power supply once and turn 
on  the  power  after  about  30 
seconds.
If  the  error  recurs,  contact  your 
nearest dealer for inspection.

Section 5  Troubleshooting

Summary of Contents for 2420






































































Reviews:

No comments