Kubota 2420 Nstruction And Service Manual Download Page 51

Page: 51 / 69

６－２

CAUTION

Make sure that the rotor yoke is firmly fastened to the drive shaft
with the rotor knob.

Since the rotor is not fastened onto the shaft when these parts are loose,excessive
vibrations will occur and damage the equipment and the rotor may fly off inflicting
physical injury.

Drive pin

Drive shaft

Center axis of rotor

Groove

If the position of the pin

▲

mark of the rotor does not align with the drive pin,

the groove at the bottom surface of the rotor and drive pin do not fit.

In such a case, reinstall the rotor.

Do not start it in the condition
that the rotor knob got loose.

６－２．

Mounting RS-1004 Rotor

1. Confirm that the

“

Bucket

intervention prevention plate

”

mounted on the drive shaft.

2.To install the rotors, match the pin

▲

mark of the rotor with the drive

pin of the drive shaft.

3. Fix the rotor yoke by rotor knob,

and then tighten by turning the
rotor knob clockwise.

4. After installation of the rotor, hold

the rotor yoke and attempt to move

it up and down to ensure that there
is no play.

Section 6 Rotor

Drive pin

Drive shaft

Bucket interven-
tion prevention plate

▲

mark indication to

align with the drive
pin at 2 places.

Screw

Rotor knob

Rotor yoke

Summary of Contents for 2420






































































Search results

Summary of Contents for 2420

Reviews:

Kubota 2420, Nstruction And Service Manual, Page: 51 / 69

Search results

Summary of Contents for 2420

Reviews: