7.30830.32.00
26
Press
↵
key to change to subfunction “RANGE I”
→
RANGE I
Selecting the measuring range
•
0-20 mA
•
4-20 mA (fixed ranges)
•
mA (user-defined range: I
0%
: 0-16 mA; I
100%
: 4-20 mA; Value I
0%
< I
100%
!)
Press
→
key to change to numerical setting.
Press
↵
key to change to subfunction “I ERROR”.
→
I ERROR
Selecting the error value
•
22 mA
•
0.0 to I
0%
mA (variable when I
0%
≥
1 mA, see above)
Press
→
key to change to numerical setting.
Press
↵
key to return to Fct. 1.05 “CURRENT OUTPUT I”.
1.06
PULS P
Pulse output P for electronic counters up to 10.000 pulses/s
→
FUNCT.P
Selecting the function for pulse output P
•
OFF
•
+ DIR.
•
- DIR. (measuring in one flow direction only)
•
2 DIR. (forward/reverse flow, F/R mode)
Press
↵
key to change to subfunction “SELECT P”.
→
SELECT P
Selecting the type of pulse
•
PULSE/VOL. (pulses per unit volume, flow rate)
•
PULSE/TIME (pulses per unit time for 100% flow rate)
Press
↵
key to change to subfunction “PULSWIDTH”.
→
PULSWIDTH
Selecting the pulse width
•
0.01 – 1.00 s (only for F
max
< 50 pulses/s)
•
AUTO (automatic = 50% of cycle duration of 100% output frequency)
•
SYM (symmetric = pulse duty factor approx. 1:1 across the entire range)
Press
↵
key to change to subfunction “VALUE P”.
→
VALUE P
Setting the pulse value per unit volume (only displayed when “PULSE/VOL.” is selected in
“SELECT P” above).
•
xxxx PulS/m3
•
xxxx PulS/Liter
•
xxxx PulS/US.Gal
•
xxxx PulS/user unit, factory setting “Liter” or “US Mgal” (see Fct. 3.05)
Setting range “xxxx” depends on pulse width and full-scale range:
P
min
= F
min
/ Q
100%
,
P
max
= F
max
/ Q
100%
Press
↵
key to return to Fct. 1.06 PULS P.
→
VALUE P
Setting the pulse value per unit time (only displayed when “PULS/TIME” is selected
in “SELECT P” above.
•
xxxx PulSe/Sec (=Hz)
•
xxxx PulSe/min
•
xxxx PulSe/hr
•
PulSe/user unit, factory setting “hr” (see Fct. 3.05).
Setting range “xxxx” depends on pulse width (see above).
Press
↵
key to return to Fct. 1.06 PULS P.
1.07
STATUS A1
or
PULS2 A1
Status output A1
A1
= terminal
connected as status or pulse output (P2)
2nd pulse output A1
see Fct. 3.07 HARDWARE, “Terminal A1”
PULS2 A1
2nd pulse output A1 for electromechanical totalizers up to max. 50 pulses/s.
Connection of terminal A1 as a 2nd pulse output A1 or as status output A1,
see Fct. 3.07 HARDWARE, “Terminal A1”.
→
FUNCT.P2
Selecting the function for pulse output P2
•
OFF
•
+ DIR.
•
- DIR. (measuring in one flow direction only)
•
2 DIR. (forward/reverse flow, F/R mode)
Press
↵
key to change to subfunction “SELECT P2”.
→
SELECT P2
Selecting the type of pulse
•
PULSE/VOL. (pulses per unit volume, flow rate)
•
PULSE/TIME (pulses per unit time for 100% flow rate)
Press
↵
key to change to subfunction “PULSWIDTH”.
→
PULSWIDTH
Selecting the pulse width
•
0.01 – 1.00 s (only for F
max
< 50 pulses/s)
•
AUTO (automatic = 50% of cycle duration of 100% output frequency)
-
•
SYM (symmetric = pulse duty factor approx. 1:1 across the entire range)
Press
↵
key to change to subfunction “VALUE P2”.
→
VALUE P2
Setting the pulse value per unit volume (only displayed when “PULSE/VOL.” is selected in
“SELECT P2” above).
•
xxxx PulS/m3
•
xxxx PulS/Liter
•
xxxx PulS/US.Gal
•
xxxx PulS/user unit, factory setting “Liter” or “US Mgal” (see Fct. 3.05)
Setting range “xxxx” depends on pulse width and full-scale range:
P
min
= F
min
/ Q
100%
,
P
max
= F
max
/ Q
100%
Press
↵
key to return to Fct. 1.07 PULS2 A1.
Setting the pulse value per unit time (only displayed when “PULS/TIME” is selected
in “SELECT P2” above.
•
xxxx PulSe/Sec (=Hz)
•
xxxx PulSe/min
•
xxxx PulSe/hr
•
PulSe/user unit, factory setting “hr” (see Fct. 3.05).
Setting range “xxxx” depends on pulse width (see above).
Press
↵
key to return to Fct. 1.07 PULS2 A1.
1.07
STATUS A1
Status output A1 (terminal A1 connected as status output A1 or as a 2nd pulse output A1,
see Fct. 3.07 HARDWARE, “terminal A1”).
1.08
1.09
1.10
STATUS A2
STATUS D1
STATUS D2
Status output A2
Status output D1
Status output D2
