![background image](http://html1.mh-extra.com/html/kramer/vsm-4x4x/vsm-4x4x_user-manual_2001470063.webp)
Kramer Electronics Ltd.
VSM-4x4X
– Protocol 3000
61
Function
Description
Syntax
Parameters/Attributes
Example
EDID-CS?
Get EDID color space.
Get command
might change the
current EDID.
COMMAND
#EDID-CS?
<direction_type>
.
<port_format>
.
<port_index>
.
<signal_type>
.
<index>
<CR>
FEEDBACK
~nn@EDID-CS
<direction_type>
.
<port_format>
.
<port_index>
.
<signal_type>
.
<index>
,
cs_mode
<CR><LF>
The following attributes comprise
the signal ID:
▪
<direction_type>
–
Direction of the port:
o
IN
– Input
o
OUT
– Output
▪
<port_format>
– Type of
signal on the port:
o
HDMI
o
ANALOG_AUDIO
▪
<port_index>
– 1-4
▪
<signal_type>
– Signal ID
attribute:
o
AUDIO
▪
<index>
1
cs_mode
– Color space
0
– RGB
1
– RGB + YUV444
2
– RGB + YUV422
3
– RGB + YUV422
4
– auto
Get EDID color space:
#EDID-CS?
in
.
hdmi
.
3
.
a
udio
.
1
,
0
<CR>
EDID-DC
Force removal of deep
color on EDID or
leaving it as in the
original EDID.
COMMAND
#EDID-DC
in_index
,
deep_color_state
<CR>
FEEDBACK
Get:
~nn@EDID-DC
in_index
,
deep_color_state
<CR><LF>
in_index
– Number that indicates
the specific input:
1-4
deep_color_state
–
0
– Don’t change
1
– Remove deep color
#EDID-DC
1
,
1
<CR>
~01@ EDID-DC 1,1
EDID-DC?
Get the input's deep
color removal status.
COMMAND
#EDID-DC?
in_index
<CR>
FEEDBACK
Get:
~nn@EDID-DC
in_index
,
deep_color_state
<CR><LF>
in_index
– Number that indicates
the specific input:
1-4
deep_color_state
–
0
– Don’t change
1
– Remove deep color
#EDID-DC 1,1<CR>
~01@ EDID-DC 1,1
EQ-LVL
Set equalization level.
COMMAND
#EQ-LVL
io_mode
,
io_index
,
eq_type
,
eq_level
<CR>
FEEDBACK
~nn@EQ-LVL
io_mode
,
io_index
,
eq_type
,
eq_level
<CR><LF>
io_mode
– Input/Output
0
– Input
1
– Output
io_index
– Number that indicates
the specific input or output port:
1-N (N= the total number of input or
output ports)
eq_type
– Equalizer Types
0
– Bass
1
– Middle
2
– Treble
eq_level
– Equalizer level (±15DB
for the PA-120Z project)
Set Bass EQ level of the
speaker output to 12:
#EQ-LVL
1
,
1
,
0
,
12
<CR>
ETH-PORT
Set Ethernet port
protocol.
If the port number
you enter is already in
use, an error is
returned.
The port number must
be within the following
range: 0-(2^16-1).
COMMAND
#ETH-PORT
port_type
,
port_id
<CR>
FEEDBACK
~nn@ETH-PORT
port_type
,
port_id
<CR><LF>
port_type
– TCP/UDP
port_id
– TCP/UDP port number
(0
– 65535)
Set the Ethernet port
protocol for TCP to port
12457:
#ETH-PORT
0
,
12457
<CR>
ETH-PORT?
Get Ethernet port
protocol.
COMMAND
#ETH-PORT?
port_type
<CR>
FEEDBACK
~nn@ETH-PORT
port_type
,
port_id
<CR><LF>
port_type
– TCP/UDP
0
– TCP
1
– UDP
port_id
– TCP / UDP port number
(0
– 65535)
Get the Ethernet port
protocol for UDP:
#ETH-PORT?
1
<CR>
FACTORY
Reset device to
factory default
configuration.
This command
deletes all user data
from the device. The
deletion can take
some time.
Your device may
require powering off
and powering on for
the changes to take
effect.
COMMAND
#FACTORY
<CR>
FEEDBACK
~nn@FACTORY
ok
<CR><LF>
Reset the device to factory
default configuration:
#FACTORY
<CR>
FEATURE-
LIST?
Get feature state
according to the
feature ID.
COMMAND
#FEATURE-LIST?
feature_id
<CR>
FEEDBACK
~nn@FEATURE-LIST
feature_id
,
ir_state
<CR><LF>
feature_id
– Feature ID)
1
– Maestro
2
– Room controller
3
– Maestro panel
ir_state
– IR interface
0
– disable
1
– enable
Get the room controller
feature state (for the room
controller 1):
#FEATURE-LIST?
1
<CR>
FORMAT
Format file system.
Response could
take several seconds
until formatting
completes.
COMMAND
#FORMAT
<CR>
FEEDBACK
~nn@FORMAT
ok
<CR><LF>
#FORMAT
<CR>