![background image](http://html1.mh-extra.com/html/kramer/vsm-4x4x/vsm-4x4x_user-manual_2001470069.webp)
Kramer Electronics Ltd.
VSM-4x4X
– Protocol 3000
67
Function
Description
Syntax
Parameters/Attributes
Example
PASS
Set password for login
level.
COMMAND
#PASS
login_level
,
password
<CR>
FEEDBACK
~nn@PASS
login_level
,
password
<CR><LF>
login_level
– Level of login to
set (End User or Administrator).
password
– Password for the
login_level
. Up to 15 printable ASCII
chars
Set the password for the
Admin protocol permission
level to 33333:
#PASS
admin
,
33333
<CR>
PASS?
Get password for login
level.
COMMAND
#PASS?
login_level
<CR>
FEEDBACK
~nn@PASS
login_level
,
password
<CR><LF>
login_level
– Level of login to
set (End User or Administrator).
password
– Password for the
login_level
. Up to 15 printable ASCII
chars
Get the password for the
Admin protocol permission
level:
#PASS?
admin
<CR>
PROT-VER?
Get device protocol
version.
COMMAND
#PROT-VER?
<CR>
FEEDBACK
~nn@PROT-VER
3000:version
<CR><LF>
version
– XX.XX where X is a
decimal digit
Get the device protocol
version:
#PROT-VER?
<CR>
RESET
Reset device
COMMAND
#RESET
<CR>
FEEDBACK
~nn@RESET
ok
<CR><LF>
Reset the device:
#RESET
<CR>
ROUTE
Set layer routing.
This command
replaces all other
routing commands.
COMMAND
#ROUTE
layer_type
,
out_index
,
in_index
<CR>
FEEDBACK
~nn@ROUTE
layer_type
,
out_index
<CR><LF>
layer_type
Layer Enumeration
1
– Video
2
– Audio
out_index
1
– OUT 1 HDMI
2
– OUT 2 HDBT
3
– OUT 3 HDBT
4
– OUT 4 HDBT
in_index
– Source id
1
– IN 1
2
– IN 2
3
– IN 3
4
– IN 4
Route video IN 2 to video
OUT 4:
#ROUTE
1,4,2
<CR>
ROUTE?
Get layer routing.
This command
replaces all other
routing commands.
COMMAND
#ROUTE?
layer_type
,
out_index
<CR>
FEEDBACK
~nn@ROUTE
layer_type
,
out_index
,
in_index
<CR><LF>
layer_type
Layer Enumeration
1
– Video
2
– Audio
out_index
1
– OUT 1 HDMI
2
– OUT 2 HDBT
3
– OUT 3 HDBT
4
– OUT 4 HDBT
in_index
– Source id
1
– IN 1
2
– IN 2
3
– IN 3
4
– IN 4
Get the layer routing:
#ROUTE?
layer
,
dest
<CR
>
SECUR
Start/stop security.
The permission
system works only if
security is enabled
with the “SECUR”
command.
COMMAND
#SECUR
security_state
<CR>
FEEDBACK
~nn@SECUR
security_state
<CR><LF>
security_state
– Security state
0
– OFF (disables security)
1
– ON (enables security)
Enable the permission
system:
#SECUR
0
<CR>
SECUR?
Get current security
state.
The permission
system works only if
security is enabled
with the “SECUR”
command.
COMMAND
#SECUR?
<CR>
FEEDBACK
~nn@SECUR
security_state
<CR><LF>
security_state
– Security state
0
– OFF (disables security)
1
– ON (enables security)
Get current security state:
#SECUR?
<CR>
SIGNAL?
Get input signal
status.
COMMAND
#SIGNAL?
in_index
<CR>
FEEDBACK
~nn@SIGNAL
in_index
,
status
<CR><LF>
in_index
– Number that indicates
the specific input:
1-4
status
– Signal status according
to signal validation:
0
– Off
1
– On
Get the input signal lock
status of IN 1:
#SIGNAL?
1
<CR>
SN?
Get device serial
number.
COMMAND
#SN?
<CR>
FEEDBACK
~nn@SN
serial_num
<CR><LF>
serial_num
– 14 decimal digits,
factory assigned
Get the device serial
number:
#SN?
<CR>
VERSION?
Get firmware version
number.
COMMAND
#VERSION?
<CR>
FEEDBACK
~nn@VERSION
firmware_version
<CR><LF>
firmware_version
–
XX.XX.XXXX where the digit groups
are: major.minor.build version
Get the device firmware
version number:
#VERSION?
<CR>