Kramer Electronics Ltd.
VSM-4x4X
– Protocol 3000
65
Function
Description
Syntax
Parameters/Attributes
Example
MODEL?
Get device model.
This command
identifies equipment
connected to
VSM-4x4X
and
notifies of identity
changes to the
connected equipment.
The Matrix saves this
data in memory to
answer REMOTE-
INFO requests.
COMMAND
#MODEL?
<CR>
FEEDBACK
~nn@MODEL
model_name
<CR><LF>
model_name
– String of up to 19
printable ASCII chars
Get the device model:
#MODEL?
<CR>
MUTE
Set audio mute.
COMMAND
#MUTE
out_index
,
mute_mode
<CR>
FEEDBACK
~nn@MUTE
out_index
,
mute_mode
<CR><LF>
out_index
– Number that
indicates the specific output:
1-4
mute_mode
– On/Off
0
– Off
1
– On
Set Output 1 to mute:
#MUTE
1
,
1
<CR>
MUTE?
Get audio mute.
COMMAND
#MUTE?
out_index
<CR>
FEEDBACK
~nn@MUTE
out_index
,
mute_mode
<CR><LF>
out_index
– Number that
indicates the specific output:
1-4
mute_mode
– On/Off
0
– Off
1
– On
Get mute status of output 1
#MUTE
1?
<CR>
NAME
Set machine (DNS)
name.
The machine
name is not the same
as the model name.
The machine name is
used to identify a
specific machine or a
network in use (with
DNS feature on).
COMMAND
#NAME
machine_name
<CR>
FEEDBACK
~nn@NAME
machine_name
<CR><LF>
machine_name
– String of up to 15
alpha-numeric chars (can include
hyphen, not at the beginning or end)
Set the DNS name of the
device to room-442:
#NAME
room-442
<CR>
NAME?
Get machine (DNS)
name.
The machine
name is not the same
as the model name.
The machine name is
used to identify a
specific machine or a
network in use (with
DNS feature on).
COMMAND
#NAME?
<CR>
FEEDBACK
~nn@NAME
machine_name
<CR><LF>
machine_name
– String of up to 15
alpha-numeric chars (can include
hyphen, not at the beginning or end)
Get the DNS name of the
device:
#NAME?
<CR>
NAME-RST
Reset machine (DNS)
name to factory
default.
Factory default of
machine (DNS) name
is “KRAMER_” + 4
last digits of device
serial number.
COMMAND
#NAME-RST
<CR>
FEEDBACK
~nn@NAME-RST
ok
<CR><LF>
Reset the machine name
(S/N last digits are 0102):
#NAME-
RST
kramer_0102
<CR>
NET-CONFIG
Set a network
configuration.
Parameters
[DNS1]
and
[DNS2]
are optional.
For Backward
compatibility, the
id
parameter can be
omitted. In this case,
the Network ID, by
default, is 0, which is
the Ethernet control
port.
If the gateway
address is not
compliant to the
subnet mask used for
the host IP, the
command will return
an error. Subnet and
gateway compliancy
specified by RFC950.
COMMAND
#NET-CONFIG
netw_id
,
net_ip
,
net_mask
,
gateway
,
[dns1]
,
[dns2
]
<CR>
FEEDBACK
~nn@NET-CONFIG
netw_id
,
net_ip
,
net_mask
,
gateway
<CR><LF>
netw_id
– Network ID–the device
network interface (if there are more
than one). Counting is 0 based,
meaning the control port is ‘0’,
additional ports are 1,2,3….
net_ip
– Network IP
net_mask
– Network mask
gateway
– Network gateway
Set the device network
parameters to IP address
192.168.113.10, net mask
255.255.0.0, and gateway
192.168.0.1:
#NET-CONFIG
0
,
192
.
168
.
113
.
10
,
255
.
255
.
0
.
0
,
1
92
.
168
.
0
.
1
<CR>
NET-CONFIG?
Get a network
configuration.
COMMAND
#NET-CONFIG?
netw_id
<CR>
FEEDBACK
~nn@NET-CONFIG
netw_id
,
net_ip
,
net_mask
,
gateway
<CR><LF>
netw_id
– Network ID–the device
network interface (if there are more
than one). Counting is 0 based,
meaning the control port is ‘0’,
additional ports are 1,2,3….
net_ip
– Network IP
net_mask
– Network mask
gateway
– Network gateway
Get network configuration:
#NET-CONFIG?
id
<CR>
