Korg Pa300, User Manual

Page: 309 / 378

305 Effects
Modulation and Pitch Shift (Mod./P.Shift)
Appe
ndix
38: St. Env. Phaser
(Stereo Envelope Phaser)
This stereo phaser uses an envelope generator for modulation.
You will obtain the same pattern of phasing each time you play.
You can also control the Phaser directly using the modulation
source.
Modulation and Pitch Shift (Mod./P.Shift)
39: Stereo Vibrato
This effect causes the pitch of the input signal to shimmer. Using
the AutoFade allows you to increase or decrease the shimmering
speed.
a
L Manu
Bottom
0...100
Sets the lower limit of the frequency
range for the effect on the left
channel
L Manu Top 0...100
Sets the upper limit of the frequency
range for the effect on the left
channel
b
R Manu
Bottom
0...100
Sets the lower limit of the frequency
range for the effect on the right
channel
R Manu Top 0...100
Sets the upper limit of the frequency
range for the effect on the right
channel
c
Sweep Mode EG, D-mod
Determines whether the flanger is
controlled by the envelope
generator or by the modulation
source
Src Off...Tempo
Selects the modulation source that
triggers the EG (when EG is selected
for Sweep Mode), or modulation
source that causes the flanger to
sweep (when D-mod is selected for
Sweep Mode)
d
EG Attack 1...100
Sets the EG attack speed
EG Decay 1...100
Sets the EG decay speed
e Resonance –100...+100
Sets the resonance amount
f High Damp [%] 0...100
Sets the resonance damping
amount in the high range
g
Wet/Dry
-Wet, -
1:99...Dry...99:1
, Wet
Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 283
Amt –100...+100 Amount of modulation source
EG Attack/Decay
EG
D-mod
Sweep Mode
D -mod
Phaser
Phaser
Left
Right
Resonance
FX Amt
FX Amt
High Damp
Stereo In - Stereo Out
a AUTOFADE Src Off...Tempo
Selects the modulation source that
starts AutoFade
b
Fade-In Delay
[msec]
00...2000
Sets the fade-in delay time
Fade-In Rate 1...100
Sets the rate of fade-in
c
LFO Waveform Triangle, Sine Selects the LFO Waveform
LFO Shape –100...+100
Changes the curvature of the LFO
Waveform
d
LFO Frequency
Mod D-mod,
AUTOFADE
Switches between D-mod and
AUTOFADE for the LFO frequency
modulation
e
LFO Frequency
[Hz]
0.02...20.00 Sets the speed of the LFO
Src Off...Tempo
Selects a modulation source for LFO
speed
Amt
–20.00...
+20.00 Sets the modulation amount of LFO
speed
f
MIDI Sync Off, On
When this is on, the LFO speed is set
by BPM, Base Note, and Times,
instead of Frequency
BPM
MIDI,
40.00...
300.00 MIDI syncs to the system tempo; 40–
300 sets the tempo manually for this
individual effect
Base Note r...w
Selects the type of notes that specify
the LFO speed
Times x1...x32
Sets the number of notes that
specify the LFO speed
g
Depth 0...100 Sets the depth of LFO modulation
Src Off...Tempo
Selects the modulation source of the
LFO modulation depth
Amt –100...+100
Sets the modulation amount of the
LFO modulation depth
h
Wet/Dry
Dry, 1:99...99:1,
Wet Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 283
Amt –100...+100 Amount of modulation source
Vibrato
Vibrato
Left
Right
FX Amt
FX Amt
Stereo In - Stereo Out
LFO: Tri / Sine LFO Shape
Fade-In Delay LFO Frequency AutoFade
Pa300 User Manual v150 (English).book Page 305 Saturday, March 29, 2014 5:29 PM