Kontron COMe-bSL6, User Manual

Page: 55 / 97

COMe-bSL6 – User Guide Rev. 1.4
www.kontron.com // 55
5.2.2. Connector X1A Row B
The following table lists the pins for connector X1A row B.
Table 30: Connector X1A Row B Pinout List
Pin COME Signal Description Type Termination Comment
B1 GND Power Ground PWR GND
B2 GBE0_ACT# Ethernet Controller activity LED indicator OD
B3 LPC_FRAME# Indicates the start of an LPC cycle O-3.3
B4 LPC_AD0 LPC multiplexed command, address and data # I/O-3.3 PU 15 k Ω to 40 k Ω
in PCH (S5)
B5 LPC_AD1
B6 LPC_AD2
B7 LPC_AD3
B8 LPC_DRQ0# LPC serial DMA/Master request # NC
B9 LPC_DRQ1#
B10 LPC_CLK LPC 24 MHz clock output O-3.3
PD 20 k
Ω
in PCH
24 MHz
B11 GND Power Ground PWR GND
B12 PWRBTN# Power Button - a falling edge creates a power
button event I-3.3 PU 10 k
Ω
, 3.3 V Power button events can
be used to bring a system
out of S5 soft-off and
other suspend states, as
well as powering the
system down.
B13 SMB_CLK SMBus clock line O-3.3 PU 2.56 k
Ω,
3.3 V
(S5)
B14 SMB_DAT SMBus bidirectional data line I/O-3.3 PU 2.56 k
Ω,
3.3 V
(S5)
B15 SMB_ALERT# SMBus alert can be used to generate a SMI# or to
wake the system I/O-3.3 PU 2.2 k
Ω,
3.3 V
(S5)
B16 S SATA 1 transmit data pair DP-O
B17 SATA1_TX-
B18 SUS_STAT# Indicates imminent suspend operation; used to
notify LPC devices. O-3.3
B19 S SATA 1 receive data pair DP-I
B20 SATA1_RX-
B21 GND Power Ground PWR GND
B22 S SATA 3 transmit data pair DP-O
B23 SATA3_TX-
B24 PWR_OK Power OK from main power supply. I-5T PU 61 k
Ω
, 3.3 V 20 V protection circuit
implemented on module
B25 S SATA 3 receive data pair DP-I
B26 SATA3_RX-
B27 WDT Indicates a watchdog time-out event has
occurred O-3.3 PD 10 k
Ω
B28 HDA_SDIN2 Audio Codec serial data input 2 NC Not supported
B29 HDA_SDIN1 Audio Codec serial data input 1 I-3.3 PD 20 k
Ω
in PCH
B30 HDA_SDIN0 Audio Codec serial data input 0
B31 GND Power Ground PWR GND
B32 SPKR Speaker output provides the PC beep signal and
is mainly intended for debugging purposes O-3.3 PD 20 k
Ω
in PCH PD is enabled until reset
is deasserted
B33 I2C_CK I2C port clock output O-3.3 PU 2.21 k
Ω,
3.3 V
(S5)
B34 I2C_DAT I2C port data I/O line I/O-3.3 PU 2.21 k
Ω,
3.3 V
(S5)
B35 THRM# Input from off-Module temp sensor indicating an
over-temp situation I-3.3 PU 10 k
Ω
to 3.3 V
(S0)
No function implemented