13
10. Maintenance and inspection
Prior to performing any maintenance or
inspection tasks, disconnect the primary
electrical power. Remove the mains plug;
position the mains switch to OFF.
First wait for the mincer feed screw and mixing blade to
come to a standstill before carrying out any work on the
machine. Wear protective goggles. When performing
work in the vicinity of the cross knife, cut-resistant
gloves should be worn.
-
Ensure compliance with the safety instructions when
performing maintenance or inspection tasks.
-
Along with many other factors, the operational safety and
service life of the machine are dependent upon proper
execution of the maintenance function.
-
Operating malfunctions resulting from insufficient or
improper maintenance can lead to high repair costs and
lengthy periods of machine downtime. For this reason,
regular maintenance is indispensable.
-
The following table contains time, inspection and
maintenance related information and instructions for
normal machine deployments.
-
Due to the widely varying operating conditions, however,
a definite schedule for wearing part checks, servicing
or maintenance cannot be established in advance. A
practical inspection schedule should be established based
on the specific on-site operating conditions.
-
Our specialists are available and would be pleased to offer
assistance in this area.
!
9. Machine type plate (example)
Motor drive capacities are dependent on machine
configuration.
Uk = Control transformer short-circuit voltage.
Weight information is dependent on machine configuration,
from - to.
Cutting system according to type of machine
F O O D T E C
Paul KOLBE GmbH • Gewerbestraße 5 • D-89275 Elchingen
Tel. +49(0) 73 08 - 96 10-0 • Fax +49(0) 73 08 - 96 10-98
Made in Germany • www.kolbe-foodtec.com
Typ
Type
Maschinenart
Indentifi cation
Baujahr
Production year
Serien-Nr.
Serial no.
Leistung
Power
Netzspannung
Supply voltage
Frequenz
Frequency
Steuerspannung
Control voltage
Gewicht
Weight
Elektroschaltplan
Wiring diagram
Sägeband
Saw band
Schneidsystem
Cutting system
kW
V
Hz
V
kg
Made in Germany • www.kolbe-foodtec.com
Paul KOLBE GmbH • Gewerbestraße 5 • D-89275 Elchingen
Tel. +49(0) 73 08 - 96 10-0 • Fax +49(0) 73 08 - 96 10-98
Typ
Type
Baujahr
Production year
Serien-Nr.
Serial no.
Elektroschaltplan
Wiring diagram
F O O D T E C
Nennstrom
Rated current
A
MWK32-45
Automatenmischfl eischwolf
20XX
XX XXXX
3,0 + 0,37
3 x 400 VAC / N / PE
50
24 VAC / UK = 16,4 V
250 - 260
XX.XX.XX
Enterprise E32
- - - - - - - -
7,1 + 1,17
3
2
1
4
3
2
1
4
10.1 Maintenance and inspection list
Inspection interval
Inspection points / Service notes
daily
• Check cutter sharpness and cutting set wear
• Check safety equipment for function, e.g. check the housing outlet protective cover, remov-
able hand guard, hopper protective cover or attachment, incl. frame protection or light barrier
protection, for shutdown function.
• Clean thoroughly according to Cleaning plan
monthly
• Check mincer feed screw knife studs for wear, renew or replace as needed
annually
• Check mincer feed screw and mincer housing for wear, renew or replace as needed
• Check gearbox mounting (in the event of bearing damage, replace ball bearing)
• Check motor mounting (in the event of bearing damage, replace ball bearing)
• Check v-belts, renew or replace as needed
every 5 to 6 years
• Change gearbox oil