background image

3  OPERATIONAL DESCRIPTION

In  network  installations 

IC-IP-S.1.0

  is  used  as  KNX  IP  interface.  A er  connecting  to  KNX  TP, 

IC-IP-S.1.0

 

operates with its default settings. Setting the correct Individual Address is necessary to include 

IC-IP-S.1.0

 

in the present KNX bus system.

3.2  IP NETWORK

IC-IP-S.1.0

  sends  telegrams  from/to  the  TP  network  to/from  the  IP  network  in  accordance  with  the 

KNXnet/IP protocol specification. Important notes:

џ

All KNX IP devices that are intended to communicate with each other via IP must have the same IP 
multicast address.

џ

I

f the IP address is changed from the IP side it may happen that ETS does no longer recognize the 

device and connection cannot be maintained (tunneling uses IP addresses). So, it is recommended 
to change IP addresses and restart only from TP side.

џ

I

f problems occur for IP address assignment please ask your network administrator.

џ

According  to  the  topology,  the  Tunneling  addresses  always  have  to  be  assigned  in  the  range  of 
subline  addresses.  For  more  information  about  additional  Individual  Addresses  for  tunneling 
please refer to IP Tunneling Address Assignment.

џ

To program devices of a line different to which the device used for (re)programming is connected, 
the use of a correct topology is mandatory!

3.1  IP INTERFACE APPLICATION

IP  Interface  is  designed  for  use  in  10/100  BaseT  networks  compliant  to  IEEE802.3.  The  AutoSensing 
function sets the baud rate (10 Mbit or 100 Mbit) automatically. IP address can be received from a DHCP 
server. For this, the automatic assignment setting of the IP address can be set by ETS (use DHCP). If set so 
and  no  DHCP  server  is  found, 

IC-IP-S.1.0

  starts  an  AutoIP  procedure  and  autonomously  assigns  the  IP 

address. The IP address that 

IC-IP-S.1.0

 receives during its start-up (via DHCP or AutoIP) is retained until 

next start-up (e.g. due to power off or reprogramming). If 

IC-IP-S.1.0

 is supposed to have a fixed IP address 

(as well as subnet mask and standard gateway) it can be set by ETS.

ETS does not provide an unload procedure for applications.

page 8

module-electronic.ru

Summary of Contents for Module IC-IP-S.1.0
























Reviews: