KNX Module IC-IP-S.1.0 User Manual Download Page 4

Page: 4 / 23

1.1 SPECIFICATION

Device model

IC-IP-S.1.0

Inputs

Ethernet connector

RJ45, female

KNX interface

Speciﬁcation

TP-256

Available application so ware

ETS 4 and later

KNX connector

4-wire EIB connector (PUSH WIRE spring clips) for standard cable TP1 0,8мм Ø

Supported protocols

KNXnet/IP, ARP, ICMP, IGMP, HTTP, UPnP discovery, UDP/IP, TCP/IP, DHCP и AutoIP

KNX physical address by default

15.15.0

Power supply

via KNX bus: 21...30В DC

Consumption on the KNX bus (29V DC)

< 20mA

< 600mW

Operation temperature

-5°C ... + 45°C

Operation humidity

5 ... 95% (no condensation)

Degree of protection

IP 20, clean environment

Mounting type

DIN rail 35mm

Dimensions

36 х 90 х 71mm (2TE)

Weight

68 g

page 4

module-electronic.ru

Summary of Contents for Module IC-IP-S.1.0
























Search results

Summary of Contents for Module IC-IP-S.1.0

Reviews:

Related manuals for Module IC-IP-S.1.0

Brands by name

Popular brands

KNX Module IC-IP-S.1.0, User Manual

Search results

Summary of Contents for Module IC-IP-S.1.0

Reviews:

Related manuals for Module IC-IP-S.1.0

Brands by name

Popular brands