Knick Stratos Pro A4 MSOXY Instruction Manual Download Page 43

Page: 43 / 140

Configuration

Menu item

Action

Choices

TC-LIQUID / CIP / SIP
Temp compensation,

process medium

For pH measurement

only: Enter temperature

compensation of the

process medium.

Enter value using





keys.

Press enter to confirm.

Cleaning cycles

on/off

MEMO SENS

Select ON or OFF using



keys.

Activates/deactivates log-

ging in extended logbook

Press enter to confirm.

ON/OFF

Sterilization cycles

on/off

MEMO SENS

Select ON or OFF using



keys.

Activates/deactivates log-

ging in extended logbook

Press enter to confirm.

ON/OFF

The cleaning and sterilization cycles are counted to measure the load

on the sensor.

Suitable for biochemical applications (process temp approx. 0...50 °C,

CIP temperature > 55 °C, SIP temperature > 115 °C).

Summary of Contents for Stratos Pro A4 MSOXY













































































































































Search results

Summary of Contents for Stratos Pro A4 MSOXY

Reviews:

Related manuals for Stratos Pro A4 MSOXY

Brands by name

Popular brands

Knick Stratos Pro A4 MSOXY, Instruction Manual

Search results

Summary of Contents for Stratos Pro A4 MSOXY

Reviews:

Related manuals for Stratos Pro A4 MSOXY

Brands by name

Popular brands