Knick Stratos Pro A4 MSOXY Instruction Manual Download Page 79

Page: 79 / 140

Time and Date

In measuring mode the time is shown in the lower display.

In addition, the logbook entries (cf Diagnostics) are provided with a

time stamp.

Please note:

• After prolonged power outage (> 5 days) the time display is

replaced by dashes and cannot be used for processing.

Enter the correct time.

• There is no automatic switchover from winter to summer time!

Be sure to manually adjust the time!

Configuration

Menu item

Action

Choices

Tag number

MEMO SENS

Select character using



keys,

select next digit using



keys.

Press enter to confirm.

A...Z, 0...9, – + < > ? / @

The first 10 characters are

seen in the display with-

out scrolling.

Tag Number (“TAG“)

You can enter a designation for the point of measurement (tag

number) in the lower display line. Up to 32 digits are possible.

Pressing meas (repeatedly) in the measuring mode indicates the tag

number.

Being part of the device configuration, the “TAG“ can be read out via

IrDA. A standardized tag number helps, for example, to correctly re-

install a device after repair.

Summary of Contents for Stratos Pro A4 MSOXY













































































































































Search results

Summary of Contents for Stratos Pro A4 MSOXY

Reviews:

Related manuals for Stratos Pro A4 MSOXY

Brands by name

Popular brands

Knick Stratos Pro A4 MSOXY, Instruction Manual

Search results

Summary of Contents for Stratos Pro A4 MSOXY

Reviews:

Related manuals for Stratos Pro A4 MSOXY

Brands by name

Popular brands