Knick Stratos Pro A4 MSOXY Instruction Manual Download Page 4

Page: 4 / 140

Contents

Documents Supplied ..................................................................... 3
Introduction .................................................................................... 7

Intended Use ......................................................................................... 7

Safety Information ......................................................................... 8
Overview of Stratos Pro A4... MSPH/MSOXY ............................. 9
Assembly ........................................................................................10

Package Contents ..............................................................................10

Mounting Plan, Dimensions ..........................................................11

Pipe Mounting, Protective Hood ..................................................12

Panel Mounting ..................................................................................13

Installation .....................................................................................14

Installation Instructions ...................................................................14

Rating Plates / Terminal Assignments ........................................14

Power Supply, Signal Lines .............................................................15

Connecting Sensors A and B .........................................................16

Connecting a Memosens Sensor ...............................................19
User Interface, Keypad ................................................................20
Display ............................................................................................21

Signal Colors (Display Backlighting) ...........................................21

Measuring Mode...........................................................................22
Selecting the Mode / Entering Values ......................................23
Operating Modes ..........................................................................24

Menu Structure of Modes and Functions .................................25

HOLD Mode .........................................................................................26

Alarm ......................................................................................................27

Overview of Configuration .........................................................28
Setup and Channel Selection on the Device ..........................29

Channel Selection and Display Assignment ............................29

Configuration (Original for Copy) ................................................35

OXY Sensor ...........................................................................................44

Summary of Contents for Stratos Pro A4 MSOXY













































































































































Search results

Summary of Contents for Stratos Pro A4 MSOXY

Reviews:

Related manuals for Stratos Pro A4 MSOXY

Brands by name

Popular brands

Knick Stratos Pro A4 MSOXY, Instruction Manual

Search results

Summary of Contents for Stratos Pro A4 MSOXY

Reviews:

Related manuals for Stratos Pro A4 MSOXY

Brands by name

Popular brands