Knick Stratos Pro A4 MSOXY Instruction Manual Download Page 44

Page: 44 / 140

Configuration

OXY Sensor

Selecting sensor type, measuring mode, calibration medium,

calibration timer

1 Press any arrow key.

2 Select CONF using



keys, press enter.

3 Select SENSOR_OXY menu using



keys,

press enter.

4 All items of this menu group are indicated by

the “OXY:” code.

Press enter to select menu,

edit with arrow keys (see next page).

Confirm (and proceed) by pressing enter.

5 End: Press meas key until the [meas] mode

indicator is displayed.

Select sensor type
Select measuring mode
Calibration medium water/air
Calibration timer
Salinity
Pressure unit
Pressure correction
Manual pressure correction
Current input
Current input/Pressure range
Cleaning cycles
Sterilization cycles

enter

MEMO SENS

enter

meas

Summary of Contents for Stratos Pro A4 MSOXY













































































































































Search results

Summary of Contents for Stratos Pro A4 MSOXY

Reviews:

Related manuals for Stratos Pro A4 MSOXY

Brands by name

Popular brands

Knick Stratos Pro A4 MSOXY, Instruction Manual

Search results

Summary of Contents for Stratos Pro A4 MSOXY

Reviews:

Related manuals for Stratos Pro A4 MSOXY

Brands by name

Popular brands