Knick Stratos Pro A4 MSOXY Instruction Manual Download Page 27

Page: 27 / 140

Alarm

Manual activation of HOLD

The HOLD mode can be activated manually from the HOLD menu. This

allows checking or replacing a sensor, for example, without provoking

unintended reactions of outputs or contacts.

Press meas key to return to selection menu.

Alarm

When an error has occurred, Err xx is displayed immediately.

Only after expiry of a user-defined delay time will the alarm be

registered and entered in the logbook.

During an alarm the display blinks, the display backlighting turns

red

Error messages can also be signaled by a 22 mA output current

(see Configuration).

The alarm contact is activated by alarm and power failure, see also

“Configuration / Alarm Settings“.

2 sec after the failure event is corrected, the alarm status will be

deleted.

External activation of HOLD

(SW-A005)

The HOLD mode can be activated from outside by sending a signal to

the Hold input (e.g. from the process control system).

Process control system

Power supply

12...24 V AC/DC

Stratos Pro A4...

input

HOLD

HOLD inactive

0...2 V AC/DC

HOLD active

10...30 V AC/DC

Summary of Contents for Stratos Pro A4 MSOXY













































































































































Search results

Summary of Contents for Stratos Pro A4 MSOXY

Reviews:

Brands by name

Popular brands

Knick Stratos Pro A4 MSOXY, Instruction Manual

Search results

Summary of Contents for Stratos Pro A4 MSOXY

Reviews:

Brands by name

Popular brands