background image

xii

HydroChart 5000 Sonar Operations and Maintenance Manual

P/N 11210080, Rev. 02

Conditions Of Warranty 

a) Seller’s warranty policy does not apply to equipment which has been subjected to 

accident, abuse, or misuse, shipping damage, alterations, incorrect and/or non-
authorized service or equipment on which the serial number plate has been 
altered, mutilated or removed. 

b) A suitable proof of purchase, such as, a paid commercial invoice, an installation 

certificate signed by Seller or an authorized agent must be made available to 
Seller or Seller’s authorized servicing agent at the time of the Warranty Service. 

c) The warranties stated herein are in lieu of all other warranties, expressed or 

implied, and of all other obligations or liabilities on the part of Seller. Seller 
neither assumes nor authorizes any other person to assume for it any other 
liability. The Buyer expressly waives any right, claim or cause of action that 
might otherwise arise out of the purchase and use of Seller’s products or service. 

d) Warranty is not transferable and only applies to the original Buyer. 

e) Warranty does not cover equipment that has been repaired or modified other than 

by Seller, or equipment that has been subjected to misuse or to negligent or 
accidental mishandling. 

f) Except where Seller has performed the installation of specific equipment, Seller 

assumes no responsibility for damage incurred during installation of equipment or 
by damage caused by no fault of the Seller. 

g) This warranty does not cover routine system checkouts or alignment/calibration, 

unless required by replacement of part(s) in the area being aligned. 

h) Consumable items are specifically excluded from this Warranty. 

i) Buyer is responsible for the prepayment of all freight charges, insurance, 

customs, imposts, duties, etc., to return defective equipment to Seller and for 
Seller to return the repaired or replaced equipment to buyer. 

j) Equipment returned for warranty service must be packed to best commercial 

standards to prevent shipping damage. 

k) Warranty shall be void and Seller shall be released from all obligations under this 

warranty if the equipment is operated with components other than those sold or 
authorized by Seller. 

l) This warranty is strictly limited to the terms and indicated herein, and no other 

warranties or remedies shall be binding on Seller including, without limitation, 
any warranties of merchantability or fitness for a particular purpose. 

m) Repairs and replacements under warranty have the same warranty as the original 

product for the remaining balance of the warranty period for the original product 
existing prior to notice of the warranty claim.

Summary of Contents for HydroChart 5000



















































































Reviews: