background image

PCR-LE2 series 

9

Turning the POWER switch off

•  PCR6000LE2, PCR9000LE2

Flip the POWER switch to the (   ) side to turn the PCR-LE2 Se-
ries off.

•  PCR12000LE2, PCR18000LE2, PCR27000LE2

Flip the MASTER POWER switch to the (   ) side to turn the 
PCR-LE2 Series off.

When the POWER switch is turned on, all items except for the fol-
lowing items take on the values that were in use the last time that 
the POWER switch was turned off.

Waveform bank contents from number 24 to number 63
Output on/off state

If the POWER switch is turned off immediately after the settings 
have been changed, the last settings may not be stored.

CAUTION

Risk of malfunction. After turning the POWER switch off, wait 

at least 5 seconds before turning it back on.

„

„

Turning off the POWER switch in an emergency

•  PCR6000LE2, PCR9000LE2

Turning off the POWER switch disconnects the product from the 
AC power line.

•  PCR12000LE2, PCR18000LE2, PCR27000LE2

Turning off the MASTER POWER switch and the two SLAVE 
POWER switches disconnects the product from the AC power 
line.

Provide enough space around the POWER switches to ensure that 
them can be turned off at any time.

Turning the Power On

Summary of Contents for PCR12000LE2















Reviews: