manualshive.com logo in svg

KidKraft NEWPORT PLAYSET F29015, Installation And Operating Instructions Manual, Page: 50 / 57

Share
Download
KidKraft NEWPORT PLAYSET F29015 Installation And Operating Instructions Manual Download Page 50

Step 29:  Attach Seat Assembly to Fort

A:

  With (1922) Seat Rail facing the fort, attach (1917) Lower Back to (1921) Seat Post using 2 (H2) 1/4 x 2” Hex 

Bolts (with lock washer, flat washer and t-nut). (fig. 29.1 and 29.2)

B:

  On the other side of the Seat Assembly attach (1920) Seat Bottom to (1921) Seat Post with 2 (H2) 1/4 x 2” 

Hex Bolts (with lock washer, flat washer and t-nut). (fig. 29.1 and 29.2)

C:

  Attach (1920) Seat Bottom to (1914) Cafe Ground with 2 Corner Braces using 3 (S5) #8 x 1/2” Pan Screws 

per brace, as shown in fig. 29.1 and 29.3.

Fig.  29.1

Fig.  29.2

Fig.  29.3

Other Parts

2 x Corner Brace

A

B

A

B

1921

1922

1920

1920

1917

1914

1914

Lock 

Washer

Lock 

Washer

1/4” Flat 

Washer

1/4” Flat 

Washer

T-Nut

Hardware

4 x 

1/4” x 2” Hex Bolt

 

(with 1/4” lock washer, 1/4” flat washer and 1/4” t-nut)

6 x 

#8 x 1/2” Pan Screw

H2

H2

H2

S5

S5

Wood Parts

1 x 

Seat Bottom 1 x 5 x 17-3/4”

1920

S5

 50 

        

[email protected]

   

Summary of Contents for NEWPORT PLAYSET F29015


























































Reviews:

No comments