manualshive.com logo in svg

KidKraft NEWPORT PLAYSET F29015, Installation And Operating Instructions Manual, Page: 17 / 57

Share
Download
KidKraft NEWPORT PLAYSET F29015 Installation And Operating Instructions Manual Download Page 17

Step 4:  Attach Swing End to Swing Beam

A:

  Place (4919) SW Rail Block in the centre between (1826) Front Beam and (1825) Back Beam and attach with 

1 (H8) 1/4 x 4-1/4” Hex Bolt (with lock washer, flat washer and t-nut). (fig. 4.1 & 4.2)

B:

 Attach Swing Beam Assembly to the side of the Swing End Assembly with the overhang (fig. 4.3 & 4.4) using 

1 (G5) 5/16 x 4-1/2” Hex Bolt (with lock washer, flat washer and t-nut) in the top hole of Triangle Plate and 1 (G8) 

5/16 x 2” Hex Bolt (with 2 flat washers and lock nut) in the bottom hole of Triangle Plate. (fig. 4.4)  Make sure 

Swing End Assembly flares out at an angle.  (fig. 4.3)

Wood Parts

Hardware

Fig. 4.2

1/4” Flat 

Washer

1/4” Lock 

Washer

1/4” 

T-Nut

H8

4919

G5

5/16” 

T-Nut

5/16”  Flat 

Washer

5/16” Lock 

Washer

5/16”  Flat 

Washer

5/16” 

Lock Nut

G8

1826

Side with 

overhang

1 x 

SW Rail Block 2 x 4 x 5-3/8”

4919

1 x 

1/4 x 4-1/4” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

1 x 

5/16 x 4-1/2” Hex Bolt (5/16” lock washer, 5/16” flat washer, 5/16” t-nut)

1 x 

5/16 x 2” Hex Bolt (5/16” flat washer x2, 5/16” lock nut)

H8
G5
G8

Fig. 4.1

Fig. 4.3

Fig. 4.4

1825

1826

1825

100

o

1826

1825

 17 

        

[email protected]

   

Summary of Contents for NEWPORT PLAYSET F29015


























































Reviews:

No comments