manualshive.com logo in svg

KidKraft NEWPORT PLAYSET F29015, Installation And Operating Instructions Manual, Page: 20 / 57

Share
Download
KidKraft NEWPORT PLAYSET F29015 Installation And Operating Instructions Manual Download Page 20

Step 6: Swing Wall Assembly

Part 2

C: 

Place (1861) SW Mount across (1924) SW Floor and (1925) SW Top and attach using 2 (G4) 5/16 x 4” Hex 

Bolts (with lock washer, flat washer and t-nut) as shown in fig. 6.2. Notice the side hole locations are towards the 

top of the board.

Note: Pre-drill all holes using a 1/8” drill bit before installing the lag screws.

D:

 Make sure assembly is square then fasten (1924) SW Floor to (1500) Posts in the top holes using 2 (LS1) 

1/4 x 1-1/2” Lag Screws (with flat washer); and (0369) Lower Diagonal to (1500) Post with 1 (LS3) 1/4 x 3” Lag 

Screw (with flat washer). (fig. 6.2)

E:

 Tighten all bolts.

Wood Parts

Hardware

1 x 

SW Mount 2 x 4 x 38-1/8”

1861

  2 x 

  5/16 x 4” Hex Bolts (5/16” lock washer, 5/16” flat washer and 5/16” t-nut)

  2 x 

  1/4” x 1-1/2” Lag Screws (1/4” flat washer)

  1 x 

  1/4” x 3” Lag Screws (1/4” flat washer)

G4

LS1

LS3

Step 6 Part 2

Fig. 6.2

1925

1924

1500

1861

G4

G4

LS1

LS3

LS1

5/16” Lock 

Washer

5/16” Flat 

Washer

1/4” Flat 

Washer

1/4” Flat 

Washer

5/16” 

T-Nut

Notice the hole

locations

 20 

        

[email protected]

   

Summary of Contents for NEWPORT PLAYSET F29015


























































Reviews:

No comments