KidKraft NEWPORT PLAYSET F29015 Installation And Operating Instructions Manual Download Page 1 | Manualshive

Page: 1 / 57

KidKraft NEWPORT PLAYSET F29015 Installation And Operating Instructions Manual Download Page 1

INSTALLATION AND OPERATING INSTRUCTIONS

NEWPORT PLAYSET – F29015

Table of Contents

Warnings and Safe Play Instructions  .  .  .  .  .  .  .  .  .  . pg . 2
Protective Surfacing Guidelines .  .  .  .  .  .  .  .  .  .  .  .  .  .  . pg . 3
Instructions for Proper Maintenance   .  .  .  .  .  .  .  .  . pg . 4
About Our Wood – Limited Warranty  .  .  .  .  .  .  .  .  . pg . 5
Keys to Assembly Success   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . pg . 7
Part ID   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . pg . 8
Step-By-Step Instructions   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .pg . 14
Installation of ID/Warning Plaque  .  .  .  .  .  .  .  .  .  .  .pg . 55

To reduce the risk of serious injury or death, you must read and

follow these instructions. Keep and refer to these instructions

often and give them to any future owner of this play set.

Manufacturer contact information provided below.

OBSTACLE FREE SAFETY ZONE - 25’1“ x 26’ area requires Protective Surfacing. See page 3.
MAXIMUM VERTICAL FALL HEIGHT - 6’ (1.8 m)
CAPACITY - 9 Users Maximum, Ages 3 to 10; Weight Limit 110 lbs. (49.9 kg) per child.RESIDENTIAL HOME USE
ONLY. Not intended for public areas such as multi-unit residences, schools, churches, nurseries, day cares or
parks.

WARNING

Rev 06/11/2018

9409015

10'2"

13'1"

25'1"

26'0"

Spring Meadow

Swing Set

KidKraft, Inc.

4630 Olin Road

Dallas, Texas 75244 USA

[email protected]

[email protected]

1.800.933.0771

972.385.0100

For online parts replacement visit

https://parts.kidkraft.com/

KidKraft Netherlands BV

Olympisch Stadion 29

1076DE Amsterdam

The Netherlands

[email protected]

+31 20 305 8620 M-F from 09:00 to 17:30

(GMT+1)

For online parts replacement visit

https://parts.kidkraft.eu/

2-4 Hrs

10 - 12 Hrs

FOR FORT & SWING

TWO PERSON

ASSEMBLY

10 - 12 Hrs

FOR FORT & SWING

4 - 8 Hrs

1
2
3
...
»

Summary of Contents for NEWPORT PLAYSET F29015


























































Reviews:

No comments