KidKraft BOULDER STATION Installation And Operating Instructions Manual Download Page 84

Page: 84 / 100

Step 34: Attach Door Dormer to Fort

Above (8197) Door Panel, flush to the top of the first (2232) Siding and tight to the centre (2181) Short Post

bolt attach Dormer from Step 7, Part 1 to (2166) Door Arch and (2186) Back Front Wall with 2 (S7) #2 x 2” Pan

Screws per (2347) Roof Block. (fig. 34.1)

Place Roof Trim Assembly with Door Roof Grill from Step 7, Part 2 centred over the pilot holes of (2348)

Roof Board A and (2349) Roof Board B and tight to the underside of each board. (fig. 34.2)

Attach (2349) Roof Board B to (2426) Roof Trim with 2 (S2) #8 x 1-1/2” Wood Screws. (fig. 34.2)

Attach (2348) Roof Board A to (2426) Roof Trim with 1 (S2) #8 x 1-1/2” Wood Screw in the bottom hole and

1 (S3) #8 x 2-1/2” Wood Screw in the top hole. (fig. 34.2)

Hardware

1 x

#8 x 2-1/2” Wood Screw

3 x

#8 x 1-1/2” Wood Screw

4 x

#12 x 2” Pan Screw

Fig. 34.1

2186

Fig. 34.2

2166

8197

2347

2348

2426

2349

Flush and Tight

Summary of Contents for BOULDER STATION





































































































Search results

Summary of Contents for BOULDER STATION

Reviews:

KidKraft BOULDER STATION, Installation And Operating Instructions Manual, Page: 84 / 100

Search results

Summary of Contents for BOULDER STATION

Reviews: