manualshive.com logo in svg

KidKraft BOULDER STATION, Installation And Operating Instructions Manual, Page: 31 / 100

Share
Download
KidKraft BOULDER STATION Installation And Operating Instructions Manual Download Page 31

 31 

 

  

Hardware

Wood Parts

4 x 

1/4 x 2” Hex Bolt 

 

(1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

4 x 

1/4 x 2-3/4” Hex Bolt 

 

(1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

H11

Step 9:  Back Wall Assembly 

Part 1

A:

  Loosely attach 1 (2180) Post  and 1 (2336) Centre Post to (2342) Ground Back with 2 (H2) 1/4 x 2” Hex Bolts 

(with lock washer, flat washer and t-nut) per board.  Make sure the bevelled end of (2180) Post is facing up.  

Notice hole orientation of board. (fig. 9.1 and 9.2)

B:

  Loosely attach (2164) Floor Support to (2180) Post and (2336) Centre Post, on front of assembly, with 2 

(H11) 1/4 x 2-3/4” Hex Bolts (with lock washer, flat washer and t-nut).   (fig. 9.1)

C:

  With bevelled ends facing up loosely attach 2 (2181) Short Posts to (2164) Floor Support with 1 (H11) 1/4 x 

2-3/4” Hex Bolt (with lock washer, flat washer and t-nut) per board.   (fig. 9.1)

1 x 

Ground Back 1 x 5 x 87-1/8”

1 x 

Post 2 x 4 x 103-3/4”

2 x 

Short Post 2 x 4 x 49-3/4”

1 x 

Centre Post 2 x 4 x 88-3/4”

1 x 

Floor Support 2 x 4 x 69-1/2”

2342

2181

2336

2164

2180

Fig. 9.2

2336

2164

2342

Fig. 9.1

1/4” lock 

washer

1/4” flat 

washer

1/4” t-nut

H2

2180

Notice bevelled 

edge facing up

2181

Inside View

H2

2180

2342

H11

H2

Notice screw hole on 

this side at bottom.

2181

H11

Summary of Contents for BOULDER STATION





































































































Reviews:

No comments