manualshive.com logo in svg

KidKraft BOULDER STATION, Installation And Operating Instructions Manual, Page: 42 / 100

Share
Download
KidKraft BOULDER STATION Installation And Operating Instructions Manual Download Page 42

 42 

 

  

Wood Parts

Hardware

Fig. 17.3

15 x 

#8 x 1-1/2” Wood Screw 

3 x 

Floor Board 1 x 4 x 35-5/8”

2197

S2

Step 17:  Floor Assembly 

Part 2

B:  

Tight to (2188) SW End and between both (2180) Posts attach 1 (2197) Floor Board to each (2164) Floor 

Support and to (2165) Joist with 5 (S2) #8 x 1-1/2” Wood Screws.  (fig. 17.3 and 17.4)

C:  

Measure 42” from (2197) Floor Board and attach a second (2197) Floor Board to each (2164) Floor Support 

and to (2165) Joist with 5 (S2) #8 x 1-1/2” Wood Screws.  (fig. 17.3 and 17.4)

D:  

Flush to the end of (2187) SL End and between both outside (2181) Short Posts attach 1 (2197) Floor Board 

to each (2164) Floor Support, (2187) SL End and (2165) Joist with 5 (S2) #8 x 1-1/2” Wood Screws.  (fig. 17.3 

and 17.4)

Fig. 17.4

2165

S2

2164

2180

2187

Slide Wall

Swing Wall

2180

2164

2197

2181

Flush 

Flush 

Tight

42”

Top View

x 5 per 

board

2180

2181

2197

Tight

2181

2197

2181

2197

2181

2197

2180

2164

2188

2188

Summary of Contents for BOULDER STATION





































































































Reviews:

No comments