KidKraft BOULDER STATION Installation And Operating Instructions Manual Download Page 35

Page: 35 / 100

Step 11: Slide Wall Assembly

4 x

1/4 x 4” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

2 x

1/4 x 4-3/4” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

1 x

SL Ground 1 x 5 x 38-1/2”

1 x

SL End 2 x 4 x 38-1/2”

2189

2187

Fig. 11.1

2189

2181

Loosely attach (2189) SL Ground to the outside of each (2336) Centre Post with 4 (H4) 1/4 x 4” Hex Bolts

(with lock washer, flat washer and t-nut). (fig. 11.1 and 11.2)

With the bolt holes towards the bottom of the board loosely attach (2187) SL End to each outside (2181)

Short Post with 2 (H6) 1/4 x 4-3/4” Hex Bolts (with lock washer, flat washer and t-nut). (fig. 11.1 and 11.3)

1/4” lock

washer

1/4” flat

washer

1/4”

t-nut

Hardware

Wood Parts

Fig. 11.2

Front Wall

Back Wall

Notice bolt

hole location

Fig. 11.3

2189

2336

2181

2187

2336

2187

1/4” lock

washer

1/4” flat

washer

1/4”

t-nut

2181

2336

Summary of Contents for BOULDER STATION





































































































Search results

Summary of Contents for BOULDER STATION

Reviews:

KidKraft BOULDER STATION, Installation And Operating Instructions Manual, Page: 35 / 100

Search results

Summary of Contents for BOULDER STATION

Reviews: