KidKraft BOULDER STATION Installation And Operating Instructions Manual Download Page 82

Page: 82 / 100

WARNING:

Bolt must not

exceed 1/2 thread past the nut

Hardware

Other Parts

Fig. 32.1

Step 32: Glider Assembly

Glider Rope

and Chain

Glider End

5/16 Flat

Washers

Glider Seat

5/16 x Glider

Long

Hex Bolt

5/16 Flat

Washer-Zinc

5/16 Lock Nut

5/16 Flat

Washer-Zinc

5/16 Lock

Nut

5/16 Lock

Nuts

Attach 1 Glider End to the Glider Seat using 1 5/16” Glider Long Hex Bolt (with 2 flat washers and 1 lock

nut). Repeat for the second Glider End. (fig. 32.1)

Install 2 Glider Rope with Chains into each Glider End using 2 - 5/16” Flat Washers and 1 Lock Nut per rope.

(fig. 32.1)

2 x Glider End
1 x Glider Seat
1 x Glider Rope and Chain (pkg of 4)

2 x

5/16” Glider Long Hex Bolt

(5/16” flat washer x 2, 5/16” lock nut)

8 x 5/16” Flat Washer
4 x 5/16” Lock Nut

Glider may not be as

shown.

Appearance may vary.

Summary of Contents for BOULDER STATION





































































































Search results

Summary of Contents for BOULDER STATION

Reviews:

KidKraft BOULDER STATION, Installation And Operating Instructions Manual, Page: 82 / 100

Search results

Summary of Contents for BOULDER STATION

Reviews: