Keysight Technologies S9106AC-2IF Startup Manual Download Page 1 | Manualshive

Page: 1 / 80

background image

STARTUP GUIDE

S9106AC-2IF, -4UP, and -42D
5G FR1 Multi-port
Transceiver Solutions

380 MHz to 6 GHz and 7 to 15 GHz

Describes the Keysight S9106AC-2IF, -4UP, and -42D 5G FR1 Multi-port Transceiver Solutions which are
streamlined, non-signaling measurement systems that enable automated testing of 5G New Radio (5G NR)
infrastructure equipment:



S9106AC-2IF 5G FR1 Multi-port Transceiver contains: two Transceiver Channels, 380 MHz to 6 GHz,
with MIMO Subsystem and 7 to 15 GHz High IF on Two Channels



S9106AC-4UP 5G FR1 Multi-port Transceiver contains: four Transceiver Channels, 380 MHz to 6 GHz,
with MIMO Subsystem



S9106AC-42D 5G FR1 Multi-port Transceiver contains: four Transceiver Channels, 380 MHz to 6 GHz,
with MIMO Subsystem and 7 to 15 GHz High IF on Two Channels

S9106AC-2IF

S9106AC-4UP

S9106AC-42D

1
2
3
...
»

Summary of Contents for S9106AC-2IF

















































































Reviews:

No comments

Related manuals for S9106AC-2IF

Brand: DayTronic Pages: 54

Brand: Bacharach Pages: 2

Brand: Bachmann Pages: 33

Brand: Make Noise Pages: 15

Brand: Major tech Pages: 40

Brand: Yamaha Pages: 10

Brand: Yamaha Pages: 38

Brand: Yamaha Pages: 45

Brand: Yamaha Pages: 48

Brand: +GF+ Pages: 8

Brand: Hanna Instruments Pages: 2

Brand: Ntron Pages: 29

Brand: NIEUWKOOP Pages: 2

Brand: Laserworld Pages: 5

Brand: XS Instruments Pages: 41

Brand: Kawai Pages: 2

WTW SensoLyt 900

Brand: Xylem Pages: 12

Brand: Bartington Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands