Keysight Technologies NFA X-Series Getting Started And Troubleshooting Manual Download Page 61

Page: 61 / 99

Keysight NFA X-Series Getting Started and Troubleshooting Guide 61

Instrument Operating System
Disk Drive Partitioning and Use

Disk Drive Partitioning and Use

The drive is partitioned into 3 sections: C:, D: and E:

— The

C: partition

contains the Windows 10 operating system and software

installed by Keysight. This is an Open System which means you can install

additional software, and these should be installed on the C: drive. However,

only a limited set of software applications are tested for use with the

Keysight measurement software. The installation and/or use of other

software is not warranted and could interfere with the operation of the

measurement software. If instrument repair is ever needed, the Keysight

version of the C: drive is the only part of the instrument software that is

restored by the Instrument Recovery process. You must reload any other

software that you have added in the instrument.

— The

D: partition

is reserved for data storage. The User Accounts that are

configured by Keysight have their My Documents folder mapped to the D:

drive. This is for the convenience of backing-up the measurement data. You

should always back-up the data on the D: drive to an external device. This

allows you to restore the data if you ever need to replace the disk drive.

— The

E: partition

is reserved for Keysight’s use. The primary use of the E:

drive is for housing the Calibration and Alignment data. Do not change or

overwrite the files on this drive. This could cause your instrument to not

meet specifications, or even to stop functioning correctly. Do not use this

drive for data storage. It is also recommended that you back up the

contents of this drive by using the factory calibration data backup utility.

Backing-up the factory calibration data

To back-up the factory calibration data you will need a USB storage device.

Table 3-3

Step

Notes

Press

System

Alignments

Backup/Restore Align Data...

An information window appears that informs you that

the instrument must shut down to complete the

backup:

"Press OK to force shut down and

proceed. Press Cancel to exit."

Summary of Contents for NFA X-Series




































































































Search results

Summary of Contents for NFA X-Series

Reviews:

Related manuals for NFA X-Series

Brands by name

Popular brands

Keysight Technologies NFA X-Series, Getting Started And Troubleshooting Manual

Search results

Summary of Contents for NFA X-Series

Reviews:

Related manuals for NFA X-Series

Brands by name

Popular brands