Keysight Technologies NFA X-Series Getting Started And Troubleshooting Manual Download Page 63

Page: 63 / 99

Keysight NFA X-Series Getting Started and Troubleshooting Guide 63

Instrument Operating System
Disk Drive Recovery Process

Disk Drive Recovery Process

The Instrument Recovery System can be used to repair errors on the

instrument's C: drive partition or to restore the original factory configuration of

the system software on the disk drive. The Instrument Recovery System is

stored in a separate hidden disk drive partition.
Repairing errors on the disk drive may result in loss of data or files. If you

require more information, see the “chkdsk” documentation in the Windows

Help and Support Center.
Restoring the original factory system software does not restore any of the

following items:

— Additional software that has been installed after the instrument was

shipped from the factory. (Thus, following an Instrument Recovery any

software installed after the instrument was shipped from the factory will

need to be re-installed.)

— System configurations (for example user accounts, windows configurations)

that have been made after the instrument was shipped from the factory.

(Thus, following an Instrument Recovery configuration changes will have to

be performed.)

— The Instrument Recovery overwrites the contents of the C: partition. It does

not affect the D: or E: partitions.

It is recommended that the customer use a regular back up strategy. The

customer’s IT department may already have a backup strategy in place which

is suitable for the instrument and its data. Using the Instrument Recovery

System in conjunction with a regular back up strategy should allow the

customer to fully recover the instrument's software and data.

Table 3-4

Recovery Process

Step

Notes

Make sure the instrument is turned

off.

Summary of Contents for NFA X-Series




































































































Search results

Summary of Contents for NFA X-Series

Reviews:

Related manuals for NFA X-Series

Brands by name

Popular brands

Keysight Technologies NFA X-Series, Getting Started And Troubleshooting Manual

Search results

Summary of Contents for NFA X-Series

Reviews:

Related manuals for NFA X-Series

Brands by name

Popular brands