5 ANALOG function
105
Unmuting the Speaker (
Audio Control
)
Type
‘
■
Standard model
■
Basic model
Description
Audio Control
is the condition which allows the transceiver to unmute the speaker by a QT tone or DQT code
and Optional Signaling.
Using KPG-D6/ D6N, the condition which allows the transceiver to unmute the speaker can be configured for
each system.
The transceiver unmutes the speaker and emits received audio if the conditions configured for Audio Control are
satisfied.
QT tone or DQT code can be combined with Optional Signaling to alter the conditions for the transceiver to
unmute the speaker.
Audio Control
Configuration
Description
QT/DQT
The transceiver unmutes the speaker if the received QT tone or DQT code
matches the QT tone or DQT code preconfigured for the transceiver. The
conditions for unmuting the speaker do not change even if the transceiver
transmits.
QT/DQT and Optional
Signaling
The transceiver does not unmute the speaker unless the received Optional
Signaling matches the Optional Signaling preconfigured for the transceiver. While
the received Optional Signaling matches the Optional Signaling preconfigured for
the transceiver, the transceiver unmutes the speaker if the received QT tone or
DQT code matches the QT tone or DQT code preconfigured for the transceiver.
QT/DQT or Optional
Signaling
While the received Optional Signaling does not match the Optional Signaling
preconfigured for the transceiver, the transceiver unmutes the speaker if the
received QT tone or DQT code matches the QT tone or DQT code preconfigured
for the transceiver.
The transceiver unmutes the speaker if the transceiver receives a carrier while
the received Optional Signaling matches the Optional Signaling preconfigured for
the transceiver. The conditions for unmuting the speaker do not change even if
the transceiver transmits.
Operating the transceiver
-
-
Note
The transceiver behaves as follows according to the type of a received signal on a channel with “Mixed”
configured in
Channel Type
.
If the transceiver receives analog signals, The transceiver behaves according to the configuration in
Audio
Control
(Analog).
Configuration using FPU
Audio Control
: Edit > Zone Information > Channel Edit > Analog
Channel Type
: Edit > Zone Information > Channel Edit > General
Selcall
Type
‘
■
Standard model
■
Basic model
Description
Optional Signaling LED
:
Optional Signaling LED
is the function that causes the LED to flash in yellow when the Optional Signaling
received matches that of the transceiver.
A user can notice by the LED that the transceiver is receiving a call.
If the matching state of Optional Signaling is disabled when the buttons on the transceiver are pressed, or when
the time configured in
Auto Reset Timer
elapses, the LED is turned off.
However, if
Selective Call Alert LED
is enabled even if
Optional Signaling LED
is enabled, the LED flashes
according to the configuration of
Selective Call Alert LED
.
Selective Call Alert LED
:
Selective Call Alert LED
is the function to make the LED flash when the transceiver receives a call.
A user can notice by the LED that the transceiver is receiving a call.
Individual Call
,
Other Selective Calls
,
Paging Call, Group Call
,
Fleet Call, All Call
:
These functions are configured how the LED responds when the transceiver receives a several calls.
Individual Call
,
Other Selective Calls
,
Paging Call
,
Status/Short Message Call
,
Emergency Response
:
These functions are selected a type of ring tone for Individual Call from 8 different types of tone configured in
Special Alert Tone. This tone sounds when the transceiver receives a several calls.
Operating the transceiver
-
-
Note
-
Configuration using FPU
Optional Signaling LED
:
Edit > FleetSync > General 2
Edit > MDC-1200 > General 2
Selective Call Alert LED
:
Edit > FleetSync > General 2
Edit > MDC-1200 > General 2 > Selcall
Individual Call
,
Other Selective Calls
,
Paging Call
:
Edit > FleetSync > General 2 > LED Color
Individual Call
,
Other Selective Calls
,
Paging Call
,
Status/Short Message Call
,
Emergency Response
:
Edit > FleetSync > General 2 > Tone Number
Individual Call
,
Group Call
,
Fleet Call, All Call
:
Edit > MDC-1200 > General 2 > Selcall > LED Color
