KENT Edge 28B Service Manual Download Page 39

Page: 39 / 46

ELECTRICAL SYSTEM

SERVICE MANUAL

ENGLISH

Edge 28B

1463165000(1)2007-02

BATTERY DISASSEMBLY/ASSEMBLY

Disassembly

Remove the hood (30) (see the procedure in the relevant paragraph).

Disconnect the connections (A) and (B) of the battery (C).

Open the battery retaining belt (D).

If necessary, loosen the screws (E) and (F), and move the battery holding brackets (G) and (H) against the edges (I) and

(J).

Remove the battery (C).

Assembly

WARNING!

If a new battery is to be installed, refer to Technical Data chapter to check which types of batteries can be

installed on this machine.

Assemble the components in the reverse order of disassembly, and note the following:

Place the battery against the edges (I) and (J), then bring the brackets (G) and (H) against the battery (C) and tighten

the screws (E) and (F). If necessary, when installing a bigger battery, use the holes (K) and (L) to hold the battery with

the brackets (G) and (H), with the screws (E) and (F).

S301612

•

Summary of Contents for Edge 28B















































Search results

Summary of Contents for Edge 28B

Reviews:

Related manuals for Edge 28B

Brands by name

Popular brands

KENT Edge 28B, Service Manual

Search results

Summary of Contents for Edge 28B

Reviews:

Related manuals for Edge 28B

Brands by name

Popular brands