KENT Edge 28B Service Manual Download Page 38 | Manualshive

Page: 38 / 46

background image

ELECTRICAL SYSTEM

ENGLISH

SERVICE MANUAL

36

1463165000(1)2007-02

Edge 28B

BATTERY CHARGER CABLE INTEGRITY CHECK

Carefully check the battery charger cable (18) and the relevant plug for wear, cuts, cracks or other damages.

If damaged:

Remove the hood (30) (see the procedure in the relevant paragraph).

Replace the cable (18).

BATTERY CHARGING

Drive the machine to the appointed recharging area and ensure that it cannot move independently.

Turn the main switch (A) to “0”.

Remove the battery charger cable (B) from the housing (C) and connect it to the electrical mains.

WARNING!

Before connecting the battery charger (B), ensure that frequency (Hz) and voltage (V) values, shown on the

machine serial number plate (33), match the electrical mains voltage.

While charging the batteries, the red warning light (D) and the yellow warning light (E) turn on in sequence.

When the green warning light (F) turns on, the batteries are charged.

Disconnect the battery charger cable (B) from the electrical mains and place it in the housing (C).

NOTE

When the battery charger is connected to the electrical mains, all machine functions are automatically

disabled.

C

B

A

F

E

D

S301611

–

–

1.

2.

3.

4.

5.

«
...
36
37
38
39
40
...
»

Summary of Contents for Edge 28B















































Reviews:

No comments

Related manuals for Edge 28B

Brand: KANSAI SPECIAL Pages: 21

Brand: Janome Pages: 31

Brand: NSS Pages: 12

ST1000E with TRS

Brand: Sure Sweep Pages: 36

Perfect Binder G10 120

Brand: Riso Pages: 78

Brand: baalbaki Pages: 8

Brand: Singer Pages: 8

Brand: ROOTS Pages: 164

Brand: HazeBase Pages: 9

Brand: Singer Pages: 32

Brand: Zhejiang Sansilou Industrial Pages: 112

Brand: Nacecare Pages: 4

Brand: Alto Pages: 51

ZEPHIRO 1000ST HAZE

Brand: soundsation Pages: 28

Brand: JUKI Pages: 50

Brand: JUKI Pages: 72

AMS-210EN Series

Brand: JUKI Pages: 249

Brand: LG Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands