manualshive.com logo in svg

KENT Edge 28B, Service Manual, Page: 4 / 46

Share
Download
KENT Edge 28B Service Manual Download Page 4

GENERAL INFORMATION

ENGLISH

SERVICE MANUAL

2

1463165000(1)2007-02

Edge 28B

CONVENTIONS

Forward, backward, front, rear, left or right are intended with reference to the operator’s position, that is to say with the hands on 

the handlebar.

MACHINE LIFTING

WARNING!

Do not work under the lifted machine without supporting it with safety stands.

MACHINE TRANSPORTATION

WARNING!

Before transporting the machine, make sure that:

All guards and hoods are closed

The machine is off

The machine is securely fastened to the means of transport.

–

–

–

OTHER AVAILABLE MANUALS

The following manuals are available at Kent Literature Service Department:

Edge 28B, Spare Parts List – Kent Form Number 146 3087 000

Edge 28B, User Manual – Kent Form Number 146 3082 000

SAFETY

The following symbols indicate potentially dangerous situations. Always read this information carefully and take all necessary 

precautions to safeguard people and property.

DANGER!

It indicates a dangerous situation with risk of death for the operator.

WARNING!

It indicates a potential risk of injury for people.

CAUTION!

It indicates a caution or a remark related to important or useful functions. Pay particular attention to the 

paragraphs marked by this symbol.

NOTE

It indicates the necessity to refer to the User Manual before performing any procedure.

CONSULTATION

It indicates that it is necessary to consult the User Manual before performing any procedure.

–

–

Summary of Contents for Edge 28B















































Reviews:

No comments