36
Operation and Service KBL 5600
7. Conections
Connecting the mains voltage
DANGER!
Live components
Risk of fatal injury due to electric shock when touching
live parts.
- Switch off mains voltage.
- Protect against re-connection.
Both the power supply and the related
connection work must comply with national
standards. The connection work must only
be performed by qualifi ed expert staff.
The connection to the 3 x 220 V mains must
be protected by fuses. Their specifi cations
are listed in the chapter “Technical data”.
A Class-A ground fault circuit interrupter
(GFCI) has to be used for Canada.
Should the operation of the tanning unit
cause any interference in the power supply
network, e.g. with ripple-control systems
(TRA), consult your power supply company
to have corresponding blocking elements
(audio frequency suppressors) installed.
The tanning device is by default set up to
operate on 3 phases but it can be changed
over to 2-phase operation. The wiring for
3-phase operation is shown below:
X5.8
X0.N3
F2.A
K2.5
K1.5
K2.3
K1.3
K2.1
K1.1
F1.A
L2(S)
L3(T)
L1(R)
D
A
B
C
X2.9
gnd
X4.3
X2.1
X4.1
X4.2
X7.3
X1.9
CA
X5.6
X2.4
X2.2
X2.3
X0.L3
E2.3
X2.5
b ase
X0.N1
X0.N2
K 6 .A2
F1.D
X1.8
X8.1
K1.5
K2.5
L
2
L
3
PE
PE
L
1
L
2
L
3
N
2
N
3
N
4
N
5
N
6
N
7
1
L
1
N
1
Mains 3 x 220V / 60Hz
The wiring for 2-phase operation is shown
below.
1.
Re-wire the 3 cables according to the dia-
gram.
2.
Make sure that you use the right cable for
the power supply.
jumper settings
change connections
s e t j u m p e r
X0.L3
X2.3
X2.2
X2.4
X5.6
CA
X1.9
X7.3
X4.2
X4.1
X2.1
X4.3
X5.8
X2.5
E2.3
b ase
K1.5
K2.5
F2.A
K1.3
K2.3
X0.N2
X0.N1
X0.N3
K1.1
K2.1
F1.A
L1(R)
D
A
B
C
X2.9
gnd
K 6 .A2
F1.D
X1.8
X8.1
L2(S)
(K 1 . 5 ) - from[X0.L3D]to[X0.L2C]
(K 2 . 5 ) - f ro m [ X 0 . L 3 D]to[X0.L2C]
(X0.N1) - from[X0.L1C]to[X0.L3D]
K2.5
K1.5
from [X0.L1]to[X0.L2]
W a g o i t e m n r . 2 0 1 6 - 4 0 2
K B L i t e m n r. 3 2 0 0 4 5 3 5 2 0
(X0.N2) - from[X0.L2C]to[X0.L3D]
N
4
N
3
N
1
N
7
N
6
N
5
N
2
L
3
L
2
PE
PE
L
1
L
1
L
2
L
3
1
change connections
1
(K2.5) > from [X0.L3D] to [X0.L2C]
2
(X0.N1) > from [X0.L1C] to [X0.L3D]
3
(K1.5) > from [X0.L3D] to [X0.L2C]
4
(X0.N2) > from [X0.L2C] to [X0.L3D]
set jumper
5
from [X0.L1] to [X0.L2]
----------------------------------
Wago item Nr.: 2016-402
KBL item Nr.: 3200453520
Mains 2 x 220V / 60Hz
Summary of Contents for megaSun 5600
Page 1: ...Operating and Maintenance KBL 5600 BA_5600_US_L 0707...
Page 56: ......