background image

EVM Modules of the MS Series Technical Introduction and User’s Guide

55

Listening To Messages Left For You With Assistance Of The

Operator (6):

When you make a call from outside, you can listen to the messages left for
you.

To help you to listen to your message operator should:

H A

Operator picks up the phone  when  the  call  arrives  and
make hook flash

B 6

Then he dials your extension number and 6

F

Operator receives dial tone.

To listen to your messages:

B

Dial  your  password,  if  one  has  been  defined,  after  the
short beep

E

You can listen to your messages.

G

Replace the handset.

Notes:

1.

 

When  the  messages  are  remotely  listened  to  like  that,  the  15-minute
erasure time-out period does not apply for them. Hence, you can listen

to the same messages again when you return to your place.

2.

 

While you are listening to your messages through this service:

-

 

If you dial

 0, 

then

 

you return to the beginning of the message you are

currently listening to.

-

 

If you dial

 1,

 then

 

you proceed to the next message.

-

 

If  you  dial

  2,

  then  you  return  to  the  point  that  is  about  3-3,5  sec

earlier and you go on listening to the same message.

-

 

If you  dial

  3, 

then,  starting  from  the  moment  you  are  in,  the  voice

level of the message is increased by one unit and you go on listening

to the message.

-

 

If you dial

 4,

 then

 

you go to the point that is about 3-3,5 sec later and

you go on listening to the same message.

PDF created with pdfFactory Pro trial version 

www.pdffactory.com

Summary of Contents for EVM38S















































































Reviews: