background image

EVM Modules of the MS Series Technical Introduction and User’s Guide

13

INSTALLATION

EVM38S:

Installation  of  EVM38S  starts  with  the  mounting  of  the  plastic  box  of  the

module on the wall. For this:

1)

 

Front cover of the EVM38S plastic box is opened by pressing the small

holes on the side faces with a screwdriver or with a similar tool that is
thin, but with a dull point, and by pulling the cover toward front at the

same time.

2)

 

The location where the module will be mounted is determined by making

use of the mounting template that comes with the module and the screw
spots are marked. (A location close to the exchange should be  chosen

for the installation by taking the length of the EVM38S connection cable
into consideration, while this operation is being fulfilled).

3)

 

The anchor plugs are driven into the wall at the marked spots without
deviating from the actual points.

4)

 

The screws are so driven to leave 7mm-portion of their heads out of the

wall.  (Heights  of  the  screw  heads  can  be  checked  by  the  edge  of  the
mounting template).

5)

 

The module is hung by  letting  the  screw  heads  pass  through  the  pear
holes at the back cover of it.

6)

 

The front cover of the module is replaced after the cable connection is
completed.

Important note

 :

 If the EVM38S  module  will  operate  together  with    MS38S

R40Ga  or  an  exchange  of  an  earlier  version,  then  the  EVM38S  converter

cable must be used.

The free and of the cable of the exchange, whose wall mounting has  been
completed,  is  connected  to  the  EVM  connector  of  the  exchange,  and  the

system setup becomes complete.

The exchange must be off during that operation.

PDF created with pdfFactory Pro trial version 

www.pdffactory.com

Summary of Contents for EVM38S















































































Reviews:

Related manuals for EVM38S