background image

11

Important Trailer Safety Information

The tire label will list the tire size that was installed on 
the trailer as original equipment when it was sold to 
you, the consumer. It also lists the maximum carrying 
capacity of the trailer.

IMPORTANT: The total weight of the load must 
never exceed the weight of cargo listed on the tire 
label and/or the maximum load carrying capacity 
listed on the VIN tag on your trailer. The GVWR 
(Gross Vehicle Weight Rating) listed is the 
maximum total weight of the trailer with accesso-
ries and all cargo allowable to be carried on the 
tires that are installed on the trailer.

WARNING: Fishtailing caused from improper 
tongue weight on the tow vehicle hitch ball can 
cause loss of control of the tow vehicle and 
resulting serious injury or property damage.

AVERTISSEMENT: Une embardée causée par un 
poids de l'attelage inapproprié sur la boule 
d'attache du véhicule remorqueur peut causer une 
perte de contrôle du véhicule remorqueur et causer 
des blessures graves et des dommages à la 

propriété

CAUTION: The maximum load applied to the trailer 
must never exceed the carrying capacity of the 
trailer as stated on the VIN label and/or the tire 
placard. Doing so may cause failure of one or more 
component parts of the trailer causing potential 
damage to the trailer and/ or a potential accident. 
All concentrated loads must be spread over as 
large an area as possible to eliminate potential 
damage to the decking.

ATTENTION: Risque de blessures causées par une 
buse mal verrouillée. Agir de la sorte risquerait de 
causer une défaillance d'une ou plusieurs 
composantes de la remorque, causant des 
dommages potentiels à la remorque et/ou un 
accident potentiel. Toutes les charges concentrées 
doivent être réparties sur une surface aussi large 
que possible pour éliminer tout dommage potentiel 
au patio

Shown next is an example of the tire label that is placed 
on your trailer showing the items just discussed above. 
Once you have familiarized yourself with the informa-
tion supplied on the example tire label and VIN tag, 
check the tire size and capacity of your trailer as shown 
on the VIN tag on your trailer.

Proper Weight Distribution & Tongue 
Weight

Ensuring that your trailer has the proper GVWR is very 
important. Once that has been established and you 
have the load on the trailer it is equally important that 
you have proper weight distribution.

Tongue Weight

The tongue weight on your trailer is 10%-15%  of the 
total weight of the trailer and all the cargo that it is 
carrying. This is the amount of weight that is then trans-
ferred to the tow vehicle through the ball hitch.

Example: The total weight of the trailer with load is 800 
pounds. The tongue weight should not be less than 80 
pounds (10%).

Too light of tongue weight can cause the trailer to “fish-
tail” (sway Weight Rating) as you travel down the 
highway. This creates excessive strains on the tow 
vehicle, hitch and on the trailer itself. It can very easily 
lead to an accident.

To adjust for too light of a tongue weight the load must 
be shifted forward with respect to the axle. This will 
increase the weight that is transferred to the tongue. 
Adjustments should be made until the tongue weight 
falls within 10% -15% recommended range. Likewise, if 
you have too much tongue weight adjust the weight 
backwards with respect to the axle until the tongue 
weight falls in the recommended range

Tow vehicles vary on how much tongue weight they can 
support for proper towing.

Karcher HDS 3.5/40 GE MT Operator’s Manual  9.807-942.0 - C

TIRE AND LOADING INFORMATION

RENSEIGNEMENTS SUR LES PNEUS ET LE CHARGEMENT

The weight of cargo should never exceed

XXXX kg or  XXXX lbs

TIRE 

SIZE 

 

 

COLD TIRE PRESS.

REAR 

XXXXXXX   

                  XXX KPA (XX  PSI)

INTER XXXXXXXXX
FRONT XXXXX
SPARE XXXXX

SEE OWNER’S
MANUAL FOR 

ADDITIONAL

INFORMATION

VOIR LE MANUAL

DE L’USAGER

POUR PLUS DE

RENSEIGNEMENTS

MANUFACTURED BY: KARCHER NORTH AMERICA INC.

DATE OF MFG.:XX/XXXX

GAWR (EACH AXLE)     

V.I.N. : 

TYPE : TRAILER

TRX-XXXX

WITH TIRES   

RIMS AT     

COLD

XXXX KG (XXXX LB)

XXXX 

XXXX   

XXX KPA (XX PSI) SINGLE

THIS VEHICLE CONFORMS TO ALL APPLICABLE U.S. FEDERAL MOTOR VEHICLE SAFETY STANDARDS
IN EFFECT ON THE DATE OF MANUFACTURE SHOWN ABOVE.

XXXXXXXXXXXXXXXXX

GVWR (XXXX KG (XXXX LB)     

Summary of Contents for Trailer HDS Series

































Reviews: