-
5
Danger of tipping when driving round
bends at high speed.
Danger of slipping on wet floors.
Drive slowly when cornering.
Danger of tipping on unstable ground.
Only use the machine on sound surfaces.
Danger of tipping with excessive sideways
tilt.
The gradient perpendicular to the direc-
tion of travel should not exceed 10%.
Step on the standing platform.
Do not press the accelerator pedal.
Release emergency-stop button by
turning.
Set main switch to “1”.
Set the speed range on the programme
selection switch.
Set the drive direction using the drive
direction button at the operator console.
Press the accelerator carefully to drive.
In case of overloading, the drive motor au-
tomatically switches off after a certain peri-
od.
Allow the appliance to cool down at
least for 5 minutes.
Step on the standing platform.
Do not press the accelerator pedal.
Release emergency-stop button by
turning.
Set main switch to “1”.
ATTENTION
Risk of damage to the floor covering. Do
not operate the appliance on the spot.
Turn the programme selector switch to
the desired function.
Set the forward drive direction using the
drive direction button at the operator
console.
Press accelerator pedal and drive to the
surface to be cleaned.
Park the machine on an even surface.
Turn key to "0" and remove it.
DANGER
Risk of injury! When loading or unloading
the machine, it may only be operated on
gradients of max. 10%. Drive slowly.
몇
CAUTION
Risk of personal injury or damage! Mind the
weight of the appliance during transport.
When transporting in vehicles, secure
the appliance according to the guide-
lines from slipping and tipping over.
Fastening points
몇
CAUTION
Risk of personal injury or damage! Consid-
er the weight of the appliance when storing
it.
This appliance must only be stored in inte-
rior rooms.
DANGER
Risk of injury! Before carrying out any tasks
on the machine, set the main key to "0" and
remove it. Pull the battery plug.
Disconnect the power cord of the charger.
몇
WARNING
Risk of injury due to overrunning suction
turbine.
Carry out maintenance tasks only after the
suction turbine has come to a halt.
Check tyre status.
Check the condition of the pad.
Check whether pads are sitting correct-
ly.
Check the pad driver plate for proper
seating.
Check if the locking lever is released for
replacing the pad driver plate.
Check if a filter bag (option) is installed.
Check the inserts of the suction hose
for leaks.
Check accelerator pedal, brake and
steering wheel for correct functioning.
Check acid level in wet batteries; refill
distilled water, if required.
Close the battery cover and the upper
part of the appliance.
Check filling level of the filter bag (op-
tion), replace if necessary.
Clean the outside of the appliance with
a damp cloth which has been soaked in
mild detergent.
Check device externally for damage.
Charge the battery:
If the charging state of the battery is un-
der 50%, charge the battery fully and
without interruption.
If the charging state of the battery is
over 50%, only recharge the battery if
the entire operation duration will be re-
quired when next used.
When used regularly, charge the bat-
tery fully and without interruption at
least once a week.
Clean upper side of the batteries.
Check acid density in wet batteries.
Check battery cable for correct position-
ing.
Check dust cover on the polishing head
for wear and damage; replace, if re-
quired (see "Maintenance tasks").
For long periods of disuse, only turn the
device off when the battery is fully
charged. Fully recharge the battery at
least every month.
Clean battery room and battery casing.
Check immobilising brake. *
Clean the joints on the polishing head
suspension.
Check carbon brushes and commuta-
tors of all motors for wear and tear. *
Check tension of steering chain. *
Check the tension of the drive chains on
the drive. *
* To be done by Customer Service.
To ensure a reliable operation of the appli-
ance maintenance contracts can be con-
cluded with the competent Kärcher sales
office.
1 Dust cover
Turn the programme selection switch to
Drive.
Turn main key to "0" and remove it.
Look for the parting point of the dust
cover and pull one end downwards out
of the holders.
Pull the remaining dust cover off hori-
zontally.
Push the new dust cover up in the indi-
vidual holders and snap in place.
Shorten the dust cover by means of
scissors or a side cutter.
DANGER
Risk of injury! Before carrying out any tasks
on the machine, set the main key to "0" and
remove it. Pull the battery plug.
Disconnect the power cord of the charger.
Disconnect the power cord of the charger.
몇
WARNING
Risk of injury due to overrunning suction
turbine.
Carry out maintenance tasks only after the
suction turbine has come to a halt.
In case of faults that cannot be remedied
using the table below please contact the
customer service.
Overload
Polishing
Shutting down
Transport
Storage
Maintenance and care
Maintenance schedule
Prior to operation:
After operation:
Weekly
Every 50 operating hours
Monthly
Every 100 operating hours
Every 200 operating hours
Maintenance Works
Maintenance contract
Replacing dust cover
Faults
14
EN
Summary of Contents for BDP 50/2000 RS Bp Bc
Page 2: ...2 ...
