Kantech IP Link Installation Manual Download Page 26 | Manualshive

Page: 26 / 37

background image

DN1670-1609

22

3. Start your web browser and enter the following IP: 192.168.1.2 and press

Enter

.

4. Enter the IP addresses as per the

Network Configuration Information Sheet

but do not click on the

Save configuration to IP Link

button yet.

5. Remove the wire between PGM2 and IN2 on the IP Link.
6. Click on the

Save configuration to IP Link

button.

7. When you will go to the site with the configured IP Link, you will have to enter the same details into

the EntraPass workstation.

«
...
24
25
26
27
28
...
»

Summary of Contents for IP Link






































Reviews:

No comments

Related manuals for IP Link

Brand: National Instruments Pages: 162

Brand: XESS Pages: 23

PG-FLEX RT FRL-752

Brand: PairGain Pages: 6

Brand: FS Pages: 19

Brand: Infoblox Pages: 13

BROADCAST POLLING FRAD BPF-14 BU

Brand: DCB Pages: 28

Brand: Uniflair Pages: 24

Brand: National Instruments Pages: 56

Brand: Kontron Pages: 62

Brand: ExtraHop Pages: 2

Brand: Cypress Semiconductor Pages: 18

Brand: Advantech Pages: 70

Brand: IBM Pages: 8

Brand: National Instruments Pages: 35

DAQ X NI 634 Series

Brand: National Instruments Pages: 278

Brand: ARX Pages: 4

Brand: Ericsson Pages: 16

Brand: InfoStor Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands