background image

DN1670-1609

18

 2. Ports used at the remote site (IP Link): Forward port 18810 to the IP address of the IP Link.

Note 1: 

If you are using more than one IP Link at the same remote site, it is necessary to use a

unique port number for each IP Link. This information is used in 

Procedure 6, Step •

Note 2: 

This port is used to configure the IP Link with a Web Browser and should not be forwarded.

This will restrict its use to the LAN only.

TCP:

 1. Ports used at the Corporate Gateway location:

Configuring the IP Link at the Remote Site

The KT-Finder is an application used to configure the IP Link over the local area network (LAN) or the
wide area network (WAN). 

Important: 

The KT-Finder application is on the EntraPass CD-ROM and is also available as a 
free download from 

www.kantech.com

. It doesn’t require any installation.

 1. Quit all EntraPass applications.
 2. Make sure there is a DHCP server on site and the IP Link is in 

Factory Default (DHCP)

 mode. See

Table 1 on page 4

.

 3. Start the KT-Finder.

Note: 

If you try to run the KT-Finder while running EntraPass, you will get an error message similar
to this.

 4. Select 

IP Link

 from the 

Device

 menu.

 Table 11: 

IP Link Ports

Purpose

Port

Broadcast and KT-Finder

18803

Communication with the Gateway

18810 (

Note 1

)

Web Configuration Page

80 (

Note 2

)

 Table 12: Gateway Ports

Purpose

Port

Firmware upgrade

18802

Communication with IP Link

18802

Summary of Contents for IP Link






































Reviews: