Kaisai MONO KHC-22RX3, Installation Manual

Page: 130 / 160

47
DHW
=
domestic hot water
Go to MENU> FOR SERVICEMAN> 1.DHW MODE
SETTING. Press OK. The following pages will be
displayed:
10.7.1 DHW MODE SETTING
1 DHW MODE SETTING
YES
YES
YES
YES
NON
ADJUST
1.1 DHW MODE
1.2 DISINFECT
1.3 DHW PRIORITY
1.4 DHW PUMP
1.5 DHW PRIORITY TIME SET
1/5
5 °C
10°C
43°C
-10°C
5 MIN
1 DHW MODE SETTING
1.6 dT5_ON
1.7 dT1S5
1.8 T4DHWMAX
1.9 T4DHWMIN
1.10 t_INTERVAL_DHW
5 °C
5 °C
30 MIN
65°C
15MIN
1 DHW MODE SETTING
1.11 dT5_TBH_OFF
1.12 T4_TBH_ON
1.13 t_TBH_DELAY
1.14 T5S_DI
1.15 t_DI HIGHTEMP.
210 MIN
30 MIN
120 MIN
YES
5 MIN
1 DHW MODE SETTING
1.16 t_DI_MAX
1.17 t_DHWHP_RESTRICT
1.18 t_DHWHP_MAX
1.19 DHWPUMP TIME RUN
1.20 PUMP RUNNING TIME
2/5
ADJUST
ADJUST
3/5
4/5
ADJUST
NON
1 DHW MODE SETTING
1.21 DHW PUMP DI RUN 5/5
ADJUST
Go to MENU> FOR SERVICEMAN> 2.COOL MODE
SETTING. Press OK.
The following pages will be displayed:
10.7.2 COOL MODE SETTING
43°C
20°C
5°C
2.0HRS
YES
1/3
2 COOL MODE SETTING
2.1 COOL MODE
2.2 t_T4_FRESH_C
2.3 T4CMAX
2.4 T4CMIN
2.5 dT1SC
ADJUST
2 °C
5MIN
10°C
16°C
35°C
2/3
2 COOL MODE SETTING
2.6 dTSC
2.7 t_INTERVAL_C
2.8 T1SetC1
2.9 T1SetC2
2.10 T4C1
ADJUST
25 °C
FCU
FLH
3/3
2 COOL MODE SETTING
2.11 T4C2
2.12 ZONE1 C-EMISSION
2.13 ZONE2 C-EMISSION
ADJUST
Go to MENU>FOR SERVICEMAN> 3.HEAT MODE
SETTING. Press OK. The following pages will be
displayed:
10.7.3 HEAT MODE SETTING
16°C
-15°C
5°C
2.0HRS
YES
3 HEAT MODE SETTING
3.1 HEAT MODE
3.2 t_T4_FRESH_H
3.3 T4HMAX
3.4 T4HMIN
3.5 dT1SH
10.7.4 AUTO MODE SETTING
Go to MENU> FOR SERVICEMAN> 4.AUTO MODE
SETTING. Press OK, the following page will be displayed.
ADJUST
35°C
28°C
-5°C
5MIN
2 °C
3 HEAT MODE SETTING
3.6 dTSH
3.7 t_INTERVAL_H
3.8 T1SetH1
3.9 T1SetH2
3.10 T4H1
ADJUST
2/3
1/3
FLH
2MIN
RAD.
7 °C
3 HEAT MODE SETTING
3.11 T4H2
3.12 ZONE1 H-EMISSION
3.13 ZONE2 H-EMISSION
3.14 t_DELAY_PUMP
ADJUST
3/3
17°C
25°C
4 AUTO. MODE SETTING
4.1 T4AUTOCMIN
4.2 T4AUTOHMAX
ADJUST
10.7.5 TEMP. TYPE SETTING
The TEMP. TYPE SETTING is used for selecting whether
the water flow temperature or room temperature is used
to control the ON/OFF of the heat pump.
When ROOM TEMP. is enabled, the target water flow
temperature will be calculated from climate-related curves
(refer to 10.1 "Climate related curves" ).
How to enter the TEMP. TYPE SETTING
Go to MENU> FOR SERVICEMAN> 5.TEMP. TYPE
SETTING. Press OK. The following page will be
displayed:
NON
NON
YES
5 TEMP. TYPE SETTING
5.1 WATER FLOW TEMP.
5.2 ROOM TEMP.
5.3 DOUBLE ZONE
ADJUST
48
If you only set WATER FLOW TEMP. to YES, or only set ROOM TEMP. to YES, The following pages will be displayed.
only WATER FLOW TEMP. YES only ROOM TEMP. YES
If you set WATER FLOW TEMP. and ROOM TEMP. to YES, meanwhile set DOUBLE ZONE to NON or YES, the following
pages will be displayed.
Homepage (zone 1)
2
Addition page (zone 2)(Double zone is effective)
◄
◄
In this case, the setting value of zone 1 is T1S,the setting value of zone 2 is TS(The corresponding TIS2 is calculated according
to the climate related curves.)
If you set DOUBLE ZONE and ROOM TEMP. to YES, meanwhile set WATER FLOW TEMP. to YES or NON,the following page
will be displayed.
Homepage (zone 1)
2
Addition page (zone 2)(Double zone is effective)
◄
◄
In this case, the setting value of zone 1 is T1S,the setting value of zone 1 is TS (The corresponding TIS2 is calculated according
to the climate related curves.)
If you set DOUBLE ZONE to YES and set ROOM TEMP. to NON, meanwhile set WATER FLOW TEMP. to YES or NON,the
following pages will be displayed.
Homepage (zone 1) Addition page (zone 2)
2
◄
◄
In this case, the setting value of zone 1 is T1S,the setting value of zone 2 is T1S2.
NON
6 ROOM THERMOSTAT
6.1 ROOM THERMOSTAT
ADJUST
About ROOM THERMOSTAT
The ROOM THERMOSTAT is used to set whether the
room thermostat is available.
How to set the ROOM THERMOSTAT
Go to MENU> FOR SERVICEMAN> 6.ROOM THERMO-
STAT. Press OK. The following page will be displayed:
10.7.6 ROOM THERMOSTAT
131 130