manualshive.com logo in svg

KAESER KCT blue T Series, Operator'S Manual

Share
Download
KAESER KCT blue T Series Operator'S Manual Download Page 44

1. DANGER! 

Electric voltage!

Risk of fatal injury caused by contact with live components!
➤ Switch off and lock out the power supply isolating device and check that no voltage is

present.

2. WARNING! 

Compressed air!

Compressed air and devices under pressure can cause serious injury or cause death if the

contained energy is released suddenly.
➤ Fully vent all pressurised components and enclosures.
➤ Verify the absence of pressure using a suitable measuring device (pressure gauge).

3. Remove and disconnect the electric cable and pressure line from the machine.
4. Position the rear panel.
5. Attach the enclosure base to the rear panel.
6. Note the motor size and position the machine with the rear rubber pads in the prepared drilled

holes in the enclosure base.

7. Push the electric cable and pressure line through the apertures provided in the font panel and

connect them.

8. Screw the front and rear panels together.

The machine fan cowl must fit snugly against the sound enclosure foam.

9. Close the sound enclosure with the cover sheet.

6

Installation

6.6

Sound enclosure retrofit

34

Operator manual    Reciprocating compressor  
KCT blue T  

No.: 902350 00E

Summary of Contents for KCT blue T Series



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands