English
Adjusting the speaker output levels
• SUBWFR LVL (subwoofer output level)
• FRONT L LVL (left front speaker output level)
• FRONT R LVL (right front speaker output level)
• CENTER LVL (center speaker output level)
• SURR L LVL (left surround speaker output level)
• SURR R LVL (right surround speaker output level)
• S BACK LVL (surround back speaker output level)
• S BACK L LVL (left surround back speaker output level)
• S BACK R LVL (right surround back speaker output level)
You can adjust the speaker output levels.
By using Precise Surround Setup (see pages 16 to 18), you can
set the output levels of all the speakers to the same levels.
Adjustable range:
–10 (dB) to +10 (dB) (in 1 dB intervals)
Initial setting:
0 (dB) for all speakers
NOTES
• If you have selected “NO” for a speaker (see page 30), the output
level for the corresponding speaker is not adjustable.
• If you have selected “1SPK” for “S BACK OUT” (see page 31), “S BACK
LVL” appears instead of “S BACK L LVL” and “S BACK R LVL.”
• While using the headphones, you cannot adjust the speaker output
levels.
Adjusting the equalization
patterns—D EQ 63Hz/250Hz/1kHz/
4kHz/16kHz
You can adjust equalization patterns in five frequency bands
(center frequency: 63 Hz, 250 Hz, 1 kHz, 4 kHz, 16 kHz) for the
front speakers.
• Once you have made an adjustment, it is memorized for
each source.
Adjustable range:
–8 (dB) to +8 (dB) (in 2 dB intervals)
Initial setting:
0 (dB) for all bands
• When making an adjustment, the DIGITAL EQ indicator
lights up on the display.
If no adjustment is required,
set all the frequency bands to
“0 (dB).”
• The DIGITAL EQ indicator goes off from the display.
From the remote control:
Before you start, remember...
There is a time limit in doing the following steps. If the
setting is canceled before you finish, start from step
1
again.
From the remote control:
1
Press TEST to check the speaker output
balance.
“TEST FL” starts flashing on the display, and test tones
come out of the speakers clockwise.
• You can adjust the speaker output levels without the
test tone.
2
Adjust the speaker output levels.
Press the + or – button corresponding to the speaker
you want to adjust.
3
Press TEST again to stop the test tone.
* When using a single speaker for the surround back
speaker, the test tone comes out of “SB” instead of “SBR”
and “SBL.”
NOTES
• No test tone comes out of the speakers for which the speaker
setting is set to “NO” (see page 30).
• No test tone is available when the headphones are in use.
• If you have selected “1SPK” for “S BACK OUT” (see page 31), press
S. BACK L +/– to adjust the output level.
• When the PSS indicator is lit, the frequency response of each
channel appears on the display with the test tone. (See page 18.)
1, 3
2
FL
=
C
=
FR
=
SR
=
SBR*
=
SBL*
=
SL
=
SW
=
(Back to the beginning)
1
Press D. EQ FREQ repeatedly to
select the band you want
to adjust.
2
Press D. EQ LEVEL + or – to
adjust the equalization
pattern of the selected
band.
3
Repeat steps
1
and
2
to
adjust other bands.
1
2
36
35-38_SoundAdj.indd 36
35-38_SoundAdj.indd 36
06.6.5 5:28:10 PM
06.6.5 5:28:10 PM
Summary of Contents for RX-D411S - AV Receiver
Page 58: ......
Page 59: ......
Page 117: ...0606RYMMDWJEIN EN FR 2006 Victor Company of Japan Limited ...
