Setting bass sound
7
Setting subwoofer output—SUBWOOFER OUT
The subwoofer emits the LFE signals* and the bass elements
of each speaker set “SML (small).”
You can also make the bass elements of the front speakers
(MAIN) emitted through the subwoofer.
SW LFE
The subwoofer emits the LFE signals and
the bass elements of the speakers set to
“SML (small).”
SW LFE+MAIN
The subwoofer emits the LFE signals and
the bass elements of the speakers set to
“SML (small).” The subwoofer also emits
the bass elements of front speakers (MAIN)
when no LFE signal nor the bass elements
of “SML (small)” speakers exist.
Initial setting:
LFE
* The LFE signals are emitted only when playing the following
software with the LFE signals:
– Dolby Digital multi-channel software
– DTS multi-channel software
When playing analog source or linear PCM software, no LFE
signal is emitted.
NOTE
When “SUBWOOFER” is set to “NO” (see page 30), you cannot select
“SUBWOOFER OUT.”
7
Setting the crossover frequency—CROSSOVER
Small speakers cannot reproduce the bass sounds efficiently.
If you use a small speaker in any position, this receiver
automatically reallocates the bass sound elements assigned to
the small speaker to the large speakers.
To use this function properly, set this crossover frequency
level according to the size of the small speaker connected.
• If you have selected “LRG (large)” for all speakers (see page
30), this function will not take effect (“CROSS OFF” appears).
• If you have performed Precise Surround Setup on pages 16
to 18, this setting is not required.
Adjustable range:
80 Hz to 200 Hz (in 10 Hz intervals)
Initial setting:
100 Hz
The following are examples of the setting:
CROSS 80Hz
Select when the cone speaker unit built in
the speaker is about 12 cm (4
3
/4 inches).
CROSS 100Hz
Select when the cone speaker unit built in
the speaker is about 10 cm (3
15
/16 inches).
CROSS 120Hz
Select when the cone speaker unit built in
the speaker is about 8 cm (3
3
/16 inches).
CROSS 150Hz
Select when the cone speaker unit built in
the speaker is about 6 cm (2
3
/8 inches).
CROSS 200Hz
Select when the cone speaker unit built in
the speaker is less than 5 cm (2 inches).
NOTE
Crossover frequency is not valid for the HEADPHONE and 3D
HEADPHONE modes.
7
Setting the low frequency effect attenuator
—LFE ATT
If the bass sound is distorted while playing back software
encoded with
Dolby Digital
or
DTS
, set the LFE level to
eliminate distortion.
• This function takes effect only when the LFE signals come in.
LFE 0dB
Normally select this.
LFE –10dB
Select when the bass sound is distorted.
Initial setting:
0 dB
Using the Midnight mode—
MIDNIGHT MODE
You can enjoy a powerful sound at night using the Midnight
mode.
When the Midnight mode is activated, the MIDNIGHT
indicator lights up on the display.
MIDNIGHT OFF
Select when you want to enjoy surround
with its full dynamic range. (No effect
applied.)
MIDNIGHT 1
Select when you want to reduce the
dynamic range a little.
MIDNIGHT 2
Select when you want to apply the
compression effect fully (useful at night).
Initial setting:
OFF
33
29-34_BasicSt.indd 33
29-34_BasicSt.indd 33
06.5.19 1:14:33 PM
06.5.19 1:14:33 PM
Summary of Contents for RX-D411S - AV Receiver
Page 58: ......
Page 59: ......
Page 117: ...0606RYMMDWJEIN EN FR 2006 Victor Company of Japan Limited ...
