JVC RX-D411S - AV Receiver Page 56 Instructions Manual Download

Page: 56 / 117

Specifications

Amplifier

Output Power

At stereo operation:

Front channels:

110 W per channel, min. RMS, driven into 6 Ω at 20 Hz to 20 kHz with no more than
0.8% total harmonic distortion.

At surround operation:

Front channels:

110 W per channel, min. RMS, driven into 6 Ω at 1 kHz with no more than 0.8% total
harmonic distortion.

Center channel:

110 W, min. RMS, driven into 6 Ω at 1 kHz, with no more than 0.8% total harmonic
distortion.

Surround channels:

110 W per channel, min. RMS, driven into 6 Ω at 1 kHz, with no more than 0.8% total
harmonic distortion.

Surround back channels:

110 W per channel, min. RMS, driven into 6 Ω at 1 kHz, with no more than 0.8% total
harmonic distortion.

Audio

Audio Input Sensitivity/Impedance:

DVR/DVD, VCR, DBS, TV:

300 mV/47 kΩ

Audio Input (DIGITAL IN)*:

Coaxial: DIGITAL IN 1(DVR/DVD):

0.5 V(p-p)/75 Ω

Optical: DIGITAL IN 2(DBS), 3(VCR):

–21 dBm to –15 dBm (660 nm ±30 nm)

USB: USB
* Corresponding to Linear PCM, Dolby Digital, and DTS (with sampling frequency—32 kHz, 44.1 kHz, 48 kHz).

Audio Output Level:

DVR, VCR:

300 mV

Signal-to-Noise Ratio (’66 IHF/’78 IHF):

80 dB/70 dB

Frequency Response (6 Ω):

20 Hz to 20 kHz (±1 dB)

Bass Boost:

+4 dB ±1 dB at 100 Hz

Equalization (at DSP operation):

Center frequency:

63 Hz, 250 Hz, 1 kHz, 4 kHz, 16 kHz

Control range:

±8 dB

Video

Video Input Sensitivity/Impedance:

Composite video: DVR/DVD, VCR, DBS:

1 V(p-p)/75 Ω

S-video: DVR/DVD, VCR, DBS:

Y (luminance):

1 V(p-p)/75 Ω

C (chrominance, burst):

0.286 V(p-p)/75 Ω

Component: DVR/DVD, VCR (DBS):

Y (luminance):

1 V(p-p)/75 Ω

, P

0.7 V(p-p)/75 Ω

Video Output Level/Impedance:

Composite video: DVR, VCR, MONITOR OUT: 1 V(p-p)/75 Ω
S-video: DVR, VCR, MONITOR OUT:

Y (luminance):

1 V(p-p)/75 Ω

C (chrominance, burst):

0.286 V(p-p)/75 Ω

Component: MONITOR OUT:

Y (luminance):

1 V(p-p)/75 Ω

, P

0.7 V(p-p)/75 Ω

Synchronization:

Negative

Designs and specifications are subject to change without
notice.

45-55_Others.indd 54

06.5.19 1:15:53 PM

Summary of Contents for RX-D411S - AV Receiver






















































































































Search results

Summary of Contents for RX-D411S - AV Receiver

Reviews:

Related manuals for RX-D411S - AV Receiver

Brands by name

Popular brands

JVC RX-D411S - AV Receiver, Instructions Manual

Search results

Summary of Contents for RX-D411S - AV Receiver

Reviews:

Related manuals for RX-D411S - AV Receiver

Brands by name

Popular brands