JVC RX-D411S - AV Receiver Page 115 Instructions Manual Download

Page: 115 / 117

English

PROBLEM

POSSIBLE CAUSE

SOLUTION

Remote control

The remote control does not
operate as you intend.

The remote control is not ready for your
intended operation.

Set the mode selector correctly, then
press the corresponding source selecting
button before operation.

The remote control does not
work.

There is an obstruction blocking the
remote sensor on the receiver.

Remove the obstruction.

Batteries are weak.

Replace batteries.

The mode selector is set to the incorrect
position.

Set the mode selector to the proper
position.

FM/AM

Continuous hiss or buzzing
during FM reception.

Incoming signal is too weak.

Connect an outdoor FM antenna (not
supplied) after unplugging the power
cord, or contact your dealer.

The station is too far away.

Select another station.

A wrong antenna is being used.

Check with your dealer to be sure you
have the correct antenna.

Antennas are not connected properly.

Check the connections.

Occasional cracking noise during
FM reception.

Ignition noise from automobiles.

Move the antenna farther from
automobile traffic.

45-54_Others.indd 53

06.6.5 5:30:39 PM

Summary of Contents for RX-D411S - AV Receiver






















































































































Search results

Summary of Contents for RX-D411S - AV Receiver

Reviews:

Related manuals for RX-D411S - AV Receiver

Brands by name

Popular brands

JVC RX-D411S - AV Receiver, Instructions Manual

Search results

Summary of Contents for RX-D411S - AV Receiver

Reviews:

Related manuals for RX-D411S - AV Receiver

Brands by name

Popular brands