JVC RX-D411S - AV Receiver Page 46 Instructions Manual Download

Page: 46 / 117

Selecting the Surround/DSP modes

From the remote control:

Select and play any source.

• Surround/DSP modes are not available when multi-

channel PCM (see page 41) signals recorded in DVD-
Audio are coming in. See page 11 for details.

• Make sure you have selected the audio input mode

(analog or digital) correctly (see page 21).

Press SURROUND repeatedly to select

the Surround/DSP mode you want.

Ex.: When “DOLBY DIGITAL” is selected for Dolby Digital
multi-channel software:

“AUTO SURROUND” is the initial setting.

Available Surround modes vary depending on the

speaker settings and the incoming signals. For details,
see page 42.

If an incoming signal is a multi-channel (more than 2

channel) digital signal, “MONO FILM” is not available.

If “SURROUND SPK” is set to “NO,” “ALL CH STEREO” is

not available.

To cancel Surround/DSP modes

Press SURROUND repeatedly so that “SURROUND OFF”
appears on the display.

On the front panel:

Before you start, remember...

There is a time limit in doing the following steps. If the setting
is canceled before you finish, start from step

again.

Select and play any source.

• Surround/DSP modes are not available when multi-

channel PCM (see page 41) signals recorded in DVD-
Audio are coming. See page 11 for details.

• Make sure you have selected the audio input setting

(analog or digital) correctly (see page 21).

Press SURROUND.

MULTI JOG now works for selecting Surround/DSP modes.

Turn MULTI JOG to select the Surround/

DSP mode you want.

Ex.: When “DOLBY DIGITAL” is selected for Dolby Digital
multi-channel software:

“AUTO SURROUND” is the initial setting.

Available Surround modes vary depending on the

speaker settings and the incoming signals. For details,
see page 42.

If an incoming signal is a multi-channel (more than 2

channels) digital signal, “MONO FILM” is not available.

If “SURROUND SPK” is set to “NO,” “ALL CH STEREO” is

not available.

To cancel Surround/DSP modes

Turn MULTI JOG so that “SURROUND OFF” appears on the
display.

1, 3

AUTO SURROUND*

Surround modes*

HALL1

HALL2

LIVE CLUB

DANCE CLUB

PAVILION

THEATER1

THEATER2

MONO

FILM*

ALL CH STEREO*

SURROUND OFF

(Back to the beginning)

AUTO SURROUND*

Surround modes*

HALL1

HALL2

LIVE CLUB

DANCE CLUB

PAVILION

THEATER1

THEATER2

MONO FILM*

ALL CH STEREO*

SURROUND OFF

(Back to the beginning)

39-44_Surround.indd 44

06.5.19 10:32:42 AM

Summary of Contents for RX-D411S - AV Receiver






















































































































Search results

Summary of Contents for RX-D411S - AV Receiver

Reviews:

Related manuals for RX-D411S - AV Receiver

Brands by name

Popular brands

JVC RX-D411S - AV Receiver, Instructions Manual

Search results

Summary of Contents for RX-D411S - AV Receiver

Reviews:

Related manuals for RX-D411S - AV Receiver

Brands by name

Popular brands