JVC RX-D411S - AV Receiver Page 69 Instructions Manual Download

Page: 69 / 117

English

NOTES

• If the AM loop antenna wire is covered with vinyl,

remove the vinyl while twisting it as shown on
the right.

• Make sure the antenna conductors do not touch

any other terminals, connecting cords and power
cord. This could cause poor reception.

Connecting the antennas

Do not connect the AC power cord until all other connections have been made.

Connecting FM and AM antennas

AM antenna connection

Connect the AM loop antenna (supplied) to the AM LOOP
terminals: Connect the white cord to the AM EXT terminal, and
connect the black cord to the

terminal.

Turn the loop until you have the best reception.
• If the reception is poor, connect an outdoor single vinyl-

covered wire (not supplied) to the AM EXT terminal. Keep
the AM loop antenna connected.

FM antenna connection

Connect the supplied FM antenna to the FM 75

Ω

COAXIAL

terminal as a temporary measure.
Extend the supplied FM antenna horizontally.
• If the reception is poor, connect an outdoor FM antenna

(not supplied). Before attaching a 75

Ω

coaxial cable with a

connector, disconnect the supplied FM antenna.

AM loop antenna (supplied)

If FM reception is poor, connect an
outdoor FM antenna (not supplied).

Snap the tabs on the loop
into the slots of the base
to assemble the AM loop
antenna.

If AM reception is poor, connect an
outdoor single vinyl-covered wire
(not supplied).

FM antenna (supplied)

Connecting the XM Connect and Play Digital Antenna

To enjoy XM Satellite Radio, connect the XM Connect and Play Digital Antenna (not supplied) to the XM jack.

XM Connect and Play Digital Antenna
(not supplied)

Black

White

NOTE

For the best reception:
– Place the XM Connect and Play Digital Antenna near a south-facing

window or where “Channel 1” can be heard clearly (see page 26).

– Make sure there is no obstruction between the XM Connect and

Play Digital Antenna and the sky.

06-15_Connection.indd 7

06.6.6 6:58:45 PM

Summary of Contents for RX-D411S - AV Receiver






















































































































Search results

Summary of Contents for RX-D411S - AV Receiver

Reviews:

Related manuals for RX-D411S - AV Receiver

Brands by name

Popular brands

JVC RX-D411S - AV Receiver, Instructions Manual

Search results

Summary of Contents for RX-D411S - AV Receiver

Reviews:

Related manuals for RX-D411S - AV Receiver

Brands by name

Popular brands