JVC KY-PZ510BE Instructions Manual Download Page 39

Page: 39 / 60

Basic Shooting

Procedures

Preparations

Supply power to the camera via a LAN cable

or AC adapter.

(

P24 [Connecting the Cables] )

Turn on the power switch.

Configure the IP address of the camera.

For viewing the IP address of the camera and

configuring the IP address.

(

P25 [Checking the IP address] )

(

P25 [IP address settings] )

Check the connection.

(

P26 [Confirming the Connection] )

Memo :

You are recommended to operate this camera

by connecting it to a PC or a controller.

The supplied infrared remote control unit might

not work depending on the conditions of

installation.

Selecting the Video

Output Resolution and

Frame Rate

This camera allows you to select the video format

for the output video.

Setting a Video Format

Set [Video]

[Video Settings]

[Video

Format].

After setting is complete, press the [Submit

＆

Reboot] button.

When [Video]

[Video Settings]

[HDMI/SDI

Output] is set to “HDMI”

3840X2160/60p, 3840x2160/59.94p,

3840x2160/50p, 3840x2160/30p,

3840x2160/29.97p, 3840x2160/25p,

1920x1080/60p, 1920x1080/59.94p,

1920x1080/50p, 1920x1080/60i,

1920x1080/59.94i, 1920x1080/50i,

1920x1080/30p, 1920x1080/29.97p,

1920x1080/25p, 1280x720/60p,

1280x720/59.94p, 1280x720/50p

When [Video]

[Video Settings]

[HDMI/SDI

Output] is set to “SDI”

1920X1080/60p, 1920x1080/59.94p,

1920x1080/50p, 1920x1080/60i,

1920x1080/59.94i, 1920x1080/50i,

1920x1080/30p, 1920x1080/29.97p,

1920x1080/25p, 1280x720/60p,

1280x720/59.94p, 1280x720/50p

Basic Shooting Procedures

Shooting

Summary of Contents for KY-PZ510BE





























































Search results

Summary of Contents for KY-PZ510BE

Reviews:

Related manuals for KY-PZ510BE

Brands by name

Popular brands

JVC KY-PZ510BE, Instructions Manual

Search results

Summary of Contents for KY-PZ510BE

Reviews:

Related manuals for KY-PZ510BE

Brands by name

Popular brands